| IR 1712 Series Parts List | |||
| Item | PartNumber | PartDescription | IR PartNumber |
| 1 | Inside Trigger Handle Assembly | 1712-A92 | |
| 2 | Grease Fitting | 130SR-188 | |
| 5 | Inside Trigger | 834-93A | |
| 6 | Inside Trigger Pin | 534-265 | |
| 7 | 8599 | Throttle Valve Plunger | 2934-302 |
| 8 | 8598 | Throttle Valve Assembly | 2934-A50 |
| 9 | 8554 | Throttle Valve Face | 2934-159 |
| 10 | 8555 | Throttle Valve Spring | 834-51 |
| 11 | 8650 | Straight Inlet | 845-565 |
| 12 | 8556 | Air Strainer Screen | 434-61 |
| 13 | Reverse Valve Seal | R00BR-210 | |
| 15 | 8558 | Handle Gasket | 2934-283 |
| 16 | Motor Clamp Washer | 2934-207 | |
| 17 | 8175 | Rear End Plate | 2934-12 |
| 18 | 8559 | Rear Rotor Bearing | 508-97 |
| 19 | 9709 | Rotor | 2934-53 |
| 20 | 2158 | Rotor Vanes (requires 6) | 2934-42-6 |
| 21 | 9707 | Cylinder | 2934-3 |
| 22 | 8730 | Front End Plate | 2934-11 |
| 23 | 8560 | Front Rotor Bearing | 810-97 |
| 24 | Cylinder Dowel | 2934-98 | |
| 25 | Motor Housing Assembly | 1712-A40 | |
| 26 | Reverse Valve Bushing | 2934-330S | |
| 27 | 8579 | Air Port Gasket (2) | R44H-210A |
| 27A | Air Port Gasket Retainer (2) | 2940-200 | |
| 28 | 8850 | Reverse Lever | 2934-658A |
| 29 | 8561 | Reverse Lock Plunger | 4U-663B |
| 30 | 8562 | Reverse Lock Plunger Spring | 4U-664 |
| 31 | Reverse Valve Assembly | 2934-A329 | |
| 32 | 8283 | Valve Seal | 85H-167 |
| 33 | Hammer Case Assembly | 1712B-A727 | |
| 34 | Hammer Case Bushing | 2934-641 | |
| 34A | Warning Label | WARNING-2-99 | |
| 35 | 8563 | Hammer Case Gasket | 2934-36 |
| 36 | Hammer Case Cap Screw (4) | 834-638 | |
| 37 | 8413 | Hammer Case Cap Screw Lockwasher (4) | 34U-58 |
| 38 | Handle Cap Screw (4) | 510-638 | |
| 39 | Handle Cap Lockwasher (4) | 8U-S8 | |
| 40 | 8851 | Hammer Frame Assembly | 2934-A703 |
| 41 | 8852A | Hammer Pin (2) | 2934-704 |
| 42 | Hammer | 1712-724 | |
| * | 8751 | Dead Handle | 834-48 |
| 43 | Side Spade Handle | T15-41 | |
| 44 | Side Spade Handle Stud | 534-148 | |
| 45 | Side Spade Handle Stud Nut | 107-73A | |
| 45A | 8885 | Side Spade Handle Bracket | 2934-364 |
| 45B | Side Spade Handle Bracket Spacer (2) | 2934-140 | |
| 46 | 1" Square Drive Anvil (standard) | 1712-726 | |
| 46 | 1" Square Drive Anvil (6" extended) | 280-726-6 | |
| 47 | Retainer Ring (for 1" square drive) | RR100155 | |
| 49 | Spline Drive Anvil (standard) | 1712-A526 | |
| 49 | Spline Drive Anvil (6" extended) | 280-A514-6 | |
| 50 | 8141 | Retaining Plunger Spring | 2940-231 |
| 51 | 8143 | Socket Retaining Ball | D04-280 |
| 52 | Retining Ball Plunger | 845-230 | |
| 53 | 8142 | Plunger Retaining Pin | 845-128 |
| 54 | Exhaust Deflector | 280-167 | |
| 55 | Exhaust Deflector Screw (2) | W54-376 | |
| 56 | Nameplate | 1712-301 | |
| 57 | Nameplate Screw (4) | C32-302 | |
| * | Exhaust Deflector Kit | 2934-K23 | |
| * | Exhaust Baffle | 2934-124 | |
| * | Gasket | 2934-223 | |
| * | Silencer | 2940P-311 | |
| * | Screw (2) | R43F-104 | |
| * | Piped-Away Exhaust Kit without Muffler | 2940-K184 | |
| * | Exhaust Adapter | 294-167 | |
| * | Exhaust Adapter Gasket | 2940-30 | |
| * | Adapter Cap Screw | AL-638 | |
| * | Exhaust Hose | R21-230 | |
| * | Hose Clamp | R21-31 | |
| * | Horizontal Hanger | 2934-366 | |
| * | 9994 | Tune-up Kit (includes illistrated parts 3, 9, 10, 12, 13, 15, 18, 20, 23, 27(2), 27A (2), 29, 30, 32 & 35) | 1712B/1712P-TK3 |
