Automotive tools & equipment

HVAC & Industrial supplies

Sales - parts -service

You are here: Home > Welder Parts - MIG > 117-078-000 83155 Century 155GS Mig 105 Amp Cold

117-078-000 83155 Century 155GS Mig 105 Amp Cold


Notes on Gun Liners:
If the gun has a red trigger, the steel liner is pn 334-468-666. If the gun has a black trigger and TWECO on the side of the handle, it uses liner KP35-40-15
117-078 Replacement Parts List
Item No.
 		Customer #
 		Description
1
246-260-000
Heat Potentiometer, 10K, 1/4 Watt
2
216-100-000
Fan Motor
3
410-900-XXX
Front Panel
4
541-057-000
Strain Relief
5
238-223-666
Cable Assembly
6
246-107-000
Knob
7
246-423-000
Power Switch, DPST Lighted
8
238-593-000
10' Mig Gun (Used on units built after 01/01/2001)

238-566-000
10' Mig Gun (Used on units built from 05/02/1999 to 12-31-2000)

238-507-000
6' Mig Gun (Used on units built before 05/03/1999)

Note On Gun Liners
If the gun has a red trigger, the steel liner is pn 334-468-666. If the gun has a black trigger and TWECO on the side of the handle, it uses liner KP1937-3
9
410-869-XXX
Control Panel
10
880-460-666
(880-569-666) Wire Speed Control
11
880-414-888
Transformer
12
410-865-XXX
Left Side Panel
13
312-295-666
Side Latch with Clip
14
246-414-000
Terminal Block
15
880-406-666
Drive Motor with Gearbox

310-187-000
Steel Drive Roller, 0.024 / 0.030 / 0.035

880-427-666
Neoprene Drive Roller for Aluminum
16

Tension Kit Less 312-110-666
17

Spindle
18
410-867-XXX
Center Panel
19
880-411-666 Circuit Board with Heat Sink
20
216-102-000
Thermostat
21
213-035-000
Capacitor, 59,000 uf, 40 Volt DC
22
880-413-666
Heat Pot. with Harness
23
253-333-666
Push In Union Fitting (5/32")
24
248-329-666
Power Cord
25
512-215-666
Bushing
26
239-074-666
Strain Relief
27
245-145-666
25 Ohm, 50 Watt Resistor
28
312-296-666
Handle
29
410-864-XXX
Right Side Panel
30
246-258-666
24 Volt DC Relay (Only on units before 01/01/2001
31
880-431-000
Base
32
246-248-000
880-426-000 Thermal Protector
33
412-635-010
Tank Bracket
34
334-460-001
Regulator (Not Shown)
35
059-217-040
40" 5/32" Gas Hose (Not Shown)
36
43090
0.025 Contact Tip (Not Shown)
37
43100
0.030 Contact Tip (Not Shown)
38
43110
0.035 Contact Tip (Not Shown)
39
43480
Steel Welding Nozzle (Not Shown)
40
312-110-666
Wire Spool Adapter (Not Shown)
41
239-010-102
Ground Clamp (Not Shown)
Sort By:
0099000132 Fan Motor 115v 120mm X 120mm (USTF120381155T) 0099000132 Fan Motor 115v 120mm X 120mm (USTF120381155T)

U.S. Toyo Fan motor Model USTF120381155T. Fan Motor provides cooling for the unit. 115 volt 120mm X 120mm X 39mm. AC Fan Axial Ball Bearing 115V 112 CFM 41dB. Designed for projects that requires cooling or ventilation; or as a replacement fan for various products. Heavy-duty aluminum Frame. Dual-ball bearings for long life. Lifespan of 67,000 hours. Fan can be laid flat or stand upright. Dimensions: 120 x 120 x 38 mm. Airflow at max speed 110 CFM. Noise at 47 dBA. Dual Ball Bearing.

Price $7.50
239-010-302 Clamp, Ground 239-010-302 Clamp, Ground

239-010-302 Clamp, Ground

Discontinued See 239-292-666
239-052-908 Lincoln Cable Connector, Set #4-#1 (4031) 239-052-908 Lincoln Cable Connector, Set #4-#1 (4031)

Lincoln Cable Conncetor Set. Precision machined from special contour extended brass. Equipped with heat and oil resistance molded covers. Easily twists into position. Model 239-052-908. One pair 3/8” brass male plugs. Fits most Century Arc and MIG welders. For cable size #4-#1

Discontinued
246-107-666 Century Knob 1-1/2" Round 1/4" Stem Diameter Black Plastic 246-107-666 Century Knob 1-1/2" Round 1/4" Stem Diameter Black Plastic

246-107-666 Century Knob 1-1/2" Round 1/4" Stem Diameter Black Plastic. Replaces 246-140-666

Price $12.85
246-258-666 Relay, 24 Volt 246-258-666 Relay, 24 Volt

246-258-666 Relay, 24 Volt

Price $53.25
246-260-000 Potentiometer 10K Ohm 246-260-000 Potentiometer 10K Ohm

246-260-000 Potentiometer 10K Ohm

Discontinued
246-414-666 Terminal Block 246-414-666 Terminal Block

246-414-666 Terminal Block

Price $21.50
253-406-666 Hose Connector 1/4" MPT X 5/32" Tube Press In 253-406-666 Hose Connector 1/4" MPT X 5/32" Tube Press In

253-406-666 Hose Connector 1/4" MPT X 5/32" Tube Press In

Price $14.88
310-187-666 Drive Roller .024/.030/.035 310-187-666 Drive Roller .024/.030/.035

310-187-666 Drive Roller .024/.030/.035

Price $39.95
312-110-666 Adaptor, Spool 312-110-666 8" Spool Adapter

312-110-666 8" Spool Adapter. 8" spool adapter for Century made welders. Works with spindles 312-076-666 or 312-066-666. For 8" spool adapter for Lincoln Electric made welders see part # KH720

Price $15.04
334-203-000 Nozzle, 1/2 Id 334-203-000 Nozzle, 1/2 Id (Each)

Tweco Style MIG Welding Nozzle, Recessed. (1 pack). Replaces Century/Lincoln part numbers: 4348, 43480, 334-203-100, 334-203-500, 334-203-908, M15578, Magnum 100, KP21T-50, 21-50. Works with most Century and Lincoln Electric welders.

Price $8.00
334-228-000 Diffuser, Gas Mig Gun Large Id 334-228-000 Diffuser, Gas Mig Gun Large Id

Diffuser, Gas Mig Gun Large Id. Gas diffuser for the following MIG guns: 4320, 238-155-000, 238-155-100, 238-155-500, 238-224-000, 238-224-100.

Discontinued see KP35-50
334-474-666 Tweco Trigger 2010-2095 334-474-666 Tweco Trigger 2010-2095

334-474-666 Tweco Trigger 2010-2095 For older 238-566 and 238-567 Mig guns.

Price $10.95
880-406-001 Gearmotor / Drive Assembly .024. Replaces part numbers 880-382-000, 880-382-001, 880-382-666, 880-406-000, 880-406-666 880-406-001 Gearmotor / Drive Assembly .024

Gearmotor / Drive Assembly  .024.  Replaces part numbers 880-382-000, 880-382-001, 880-382-666, 880-406-000, 880-406-666

Price $175.00
880-411-666 Circuit Board/Rectifier Assembly 880-411-666 Circuit Board/Rectifier Assembly

Circuit Board / Heatsink assembly. Used on 117-077 2155 Solar 90 amp mig, 30-125 infinite amp range,cold, 83137 Century, 135GS mig 90 amp, 83136 Century, 135GL, 83155 Century, 155GS Mig, 83156 Century, 155GL Flux

Price $150.00
880-427-666 Roller, Composite Drive 880-427-666 Roller, Composite Drive

880-427-666 Neoprene Drive Roller For Aluminum. Used on drive base assembly 880-406-001, 880-382-000, 880-382-001, 880-382-666, 880-406-000, & 880-406-666.

Price $39.50
880-460-666 Wire Speed Control Assembly 880-460-666 Wire Speed Control Assembly

880-460-666 Wire Speed Control Assembly

Price $75.00
ED030631 Lincoln Electric Welding Wire .030 ER70S-6 SUPERARC L-56 Mig 2# Spool ED030631 Lincoln Electric Welding Wire .030 ER70S-6 SUPERARC L-56 Mig 2# Spool

Mild Steel MIG Wire (AWS ER70S-6). Lincoln’s premium copper coated MIG wire, Super Arc® L-56 is an excellent choice for welding on metals with a medium to high presence of millscale. For best performance use on clean, oil-free, and rust-free base material. Best weld appearance and toe wetting when compared to ER70S-3 and ER70S-4 classifications. Super Arc® L-56 has high silicon and manganese deoxidizer levels. Superior feedability and excellent arc characteristics are trade-marks of Super Arc® L-56. Shielding gases include argon/carbon dioxide blends, argon/ oxygen blends, straight carbon dioxide, and three or four-part gas blends.

Price $11.36
ED030632 Lincoln Electric Welding Wire .035 ER70S-6 SUPERARC L-56 Mig 2# Spool ED030632 Lincoln Electric Welding Wire .035 ER70S-6 SUPERARC L-56 Mig 2# Spool

Mild Steel MIG Wire (AWS ER70S-6). Lincoln’s premium copper coated MIG wire, Super Arc® L-56 is an excellent choice for welding on metals with a medium to high presence of millscale. For best performance use on clean, oil-free, and rust-free base material. Best weld appearance and toe wetting when compared to ER70S-3 and ER70S-4 classifications. Super Arc® L-56 has high silicon and manganese deoxidizer levels. Superior feedability and excellent arc characteristics are trade-marks of Super Arc® L-56. Shielding gases include argon/carbon dioxide blends, argon/ oxygen blends, straight carbon dioxide, and three or four-part gas blends.

Price $6.32
KH710 Lincoln .025" Tweco Style Contact Tip (10 Pack). Same as KP11-25, KP2039-1B1, M15522, Mig023 KH710 Lincoln .025" Tweco Style Contact Tip (10 Pack)

KH710 Lincoln .025" Tweco Style Contact Tip (10 Pack). Same as KP11-25, KP2039-1B1, M15522, Mig023, Replaces Century and Marquette Part Numbers:4309, 43090, 334-159-000, 334-159-300, 334-159-908, M15522, KP11-25 & Others. Used on Century made welders model 117-001 to 117-090.

Price $13.95
KH712 Lincoln .035" Tweco Style Contact Tip (10 Pack) Replaces KH712, KP11-35, KP2039-3B1, M15524, Mig035. KH712 Lincoln .035" Tweco Style Mig Contact Tip (10 Pack)

KH712 Lincoln .035" Tweco Style Contact Tip (10 Pack) Replaces KH712, KP11-35, KP2039-3B1, M15524, Mig035. Replaces Century and Marquette Part Numbers: 4311, 43110, 334-161-000, M15524, KP11-35 & Others. Used on Century made welders model 117-001 to 117-090.

Price $13.95
KH725 Lincoln Mig Gas Nozzle KH725 Lincoln Mig Gas Nozzle

KH725 Lincoln Mig Gas Nozzle. The nozzle protects threads and openings during the MIG welding process, directs shielding Gas around the tip and MIG wire for protection. Use when welding with shielding Gas only.

Price $11.70
KP35-40-15 Lincoln Electric Steel Liner .023 - .035 KP35-40-15 Lincoln Electric Steel Liner .023 - .035

KP35-40-15 Lincoln Electric Steel Liner .023 - .035, Replaces Part# 334-476-666, KP2013-1, KP1937-3.

Price $29.75
KP35-50 Diffuser, Gas Mig Gun Large Id KP35-50 Diffuser, Gas Mig Gun Large Id

Diffuser, Gas Mig Gun Large Id. Gas diffuser for the following MIG guns: 4320, 238-155-000, 238-155-100, 238-155-500, 238-224-000, 238-224-100.

Price $15.99
Portable Wire Feed Welder Owners Manual Wire Feed Welder Owners Manual

This Operators manual provides specific information for your model. This manual contains information such as the Important Safety Instructions, Usage and Maintenance of your Welder. This document is provided as a download PDF format. We suggest you save it to your computer for future reference.
Model Coverage: 117-078, 83155, 83156, 20559, Migmaster 150

Price $8.00
   
 
117-078-000 83155 Century 155GS mig 105 amp cold