0000000244 Schumacher 30 Amp Fuse Holder

0000000722 Schumacher Lamp 5 watt 14 Volt

115 Volt Power Cord

74" Long 16 AWG/3 SJTOW Power Cord. 115 Volt. Black 1/4" Quick Disconnect , White 1/4" Quick Disconnect with Piggy Back Spade, Green ring terminal.

0090026054 Schumacher 115 Volt Power Cord 18/3 74" Long 18 AWG/3 SJTOW Power Cord. 115 Volt. Black 1/8" Quick Disconnect , White Split Wire Quick Disconnect

Power Cord

115 Volt Power Cord 3 Prong. Termination Specs, 1/8" Shielded Female Quick Connect (Black), Ring Terminal (Ground), Split Terminal (Black).

0090026062 Schumacher 115 Volt Power Cord 18/3 84" Long Black 1/4" Quick Disconnect , White Split Wire Quick Disconnect, Green ring terminal.

Power Cord

Power Cord

Power Cord 115 Volt 3 Prong. Termination Specs, 1/8" Shielded Female Quick Connect (White), Ring Terminal (Ground), Split Terminal (Black).

115 Volt Power Cord 2 Wire Plug. Termination Specs, Split Terminal (Black), Split Terminal (Black).

115 Volt Power Cord 2 Wire Plug. Termination Specs, 1/4" Quick Disconnect (White), Split Terminal (Black).

0090026088 Schumacher 115 Volt Power Cord 14/2 74" Long Black Split Wire Quick Disconnect, White Split Wire Quick Disconnect.

Power Cord. See 0090026218 as a possible replacement. (The termination ends will have to be changed)

Power Cord 115 Volt 3 Prong. Termination Specs, 1/4" Quick Connect (Black), Ring Terminal (Ground), Stripped Wire (White).

0090026121 Schumacher Power Cord. SJTOWA, 14 Gauge 3 conductor 9' long .25" X .25 X RIN Termination

Power Cord 115 Volt 3 Prong. Termination Specs, 1/4" Quick Connect (Black), Ring Terminal (Ground), 1/4" Quick Connect (White).

Power Cord 115 Volt 3 Prong. Termination Specs 16/3 84", 1/4" Quick Connect (Black), Ring Terminal (Ground), 1/4" Quick Connect (White) with Strain Relief. When Discontinued See 0090026136

Power Cord

Power Cord 115 Volt 3 Prong. Termination Specs, 1/4" Quick Connect (Black), Ring Terminal (Ground), Split Terminal (White) with Strain Relief.

Power Cord

0090026135 Schumacher Power Cord 18/2

0090026136 Schumacher Power Cord 115 Volt 3 Prong. Termination Specs, 1/4" Quick Connect (Black), Ring Terminal (Ground), 1/4" Quick Connect (White) with Strain Relief.

0090026140 Schumacher Power Cord 16/3 90". Termination Specs, 1/4" Quick Connect (Black), Ring Terminal (Ground), 1/4" Quick Connect (White) with Strain Relief.

115 Volt Power Cord SJTOW 14-3, 122" 3 Prong. Termination Specs, 1/4" Quick Connect (Black), Ring Terminal (Ground), 1/4" Quick Connect Piggy Back (White) with Strain Relief.

115 Volt Power Cord SJTOW 14-3, 122" .25 Quick Disconnect /.25 Quick Disconnect / Ring Terminal connectors

0090026204 Schumacher 115 Volt Power Cord SJTOW 14/3 122"

115 Volt Power Cord

115 Volt Power Cord

0090026217 Schumacher 115 Volt Power Cord 86" 14/3 SJTOW terminals .25 x .25 S/R

0090026218 Schumacher 115 Volt Power Cord 86" 14/3 SJTOW Termination Specs, 1/4" Quick Connect (Black), Ring Terminal (Ground), 1/4" Quick Connect (White).

0090026219 Schumacher 115 Volt Power Cord

115 Volt Power Cord 18/3 84" Power Cord. 1/4" Quick Disconnect Terminals.

0093026421 Schumacher Logic Transformer 12 Volt CS-810A

0093026459 Schumacher Transformer 1.5a Amp 12 Volt INC-812A

0093026565 Schumacher Internal Charger For Jump Starter DC Power Source. 15.6 Volt, 600mA output.

0093026601 Schumacher 115v Wall Charger . Fits Schumacher IPD-1800 Jump Starters and power supplies.  Please consult your manual to ensure the correct part number before ordering.

0093026670 Schumacher Battery Charger Transformer 4/15/60/300A-6/12/24V EEBC500

0093026727 Schumacher 115 Volt Jump Starter Charger. Fits most Schumacher Jump Starters and power supplies.  Please consult your manual to ensure the correct part number before ordering.

0093026728 Schumacher Transformer 15.6V / 0.6 Amp

0093026737 Schumacher 115v Wall Charger. Please consult your manual to ensure the correct part number before ordering. Compatible with 200.71988 Sears DieHard, XP2260 Schumacher, IP-1800I Schumacher, 200.71987 Sears DieHard, 200.71990 Sears DieHard, PP-2200 Schumacher, 200.71487 Sears DieHard, 200.71488 Sears DieHard.

0093026747 Schumacher Internal Transformer 600mA

0093026896 Schumacher Transformer. 325mA Class II Open Frame. Primary 120 vac, Secondary 15.6 vac 350mA.

0093026927 Schumacher 115 Volt Wall Charger 17 volt 1 Amp

0093026931Z Schumacher Car Charger SL1

0093026932Z Schumacher 115 Volt Wall Charger 15 volt .5 Amp

Schumacher WM-12 Battery Charger 18" Ring Terminal Quick Disconnect With Dust Cover, Ring terminal and plug set makes easy access to battery for seasonal charging. Left installed on battery, you can simply plug in and walk away. Designed for permanent connection. Great for hard-to-reach motorcycle batteries. WM-12 Schumacher Ring Adapter Set Fits MC-1 SEM-1562A SC-200A SC-300A

Schumacher Battery Charger 3 Amp Fused Quick Disconnect with dust cover. Ring terminal and plug set makes easy access to battery for seasonal charging. Left installed on battery, you can simply plug in and walk away. Designed for permanent connection. Great for hard-to-reach motorcycle batteries. Works On Most Schumacher Small Chargers.

0094500507 Schumacher Halogen Bulb

0094500812 Schumacher NATO Cable Aux Red 2mm Plug

This Knob is for selector switches on SE Series chargers only, there are separate knobs for selector switches and timers. Please check your part numbers carefully.

0099000062 Schumacher 6" CW Fan Blade.

Fan Motor Open Frame 115 Volt

0099000066 Schumacher Battery Charger Axle 3/8 Dia.15-3/8" Long.

0099000068 Schumacher 115 Volt 12 Hour Timer. Electronically controls battery charging in timed Mode with manual hold mode. All circuits are rated 15 amperes. Termination is designed to accept standard 1/4" spade terminals.

0099000080 Wheel 6" Plastic For 3/8 Axle

Mechanically controls charging in timed Mode with manual hold mode. Single Pole Single Throw (SPST) Switch rated 15 amperes. Termination is designed to accept 1/4" spade terminals.

0099000096 Knob For Timer Switches 1/4" OD 3/4 "D" Shaft, there are separate knobs for selector switches and timers. Please check your part numbers carefully.

0099000120 Schumacher Wheel 7" Plastic For 3/8 Axle

0099000123 Foot For 6" Wheeled Units

Front Panel Leadset Output Connector With Cap. Includes black and red lead with spade. Easy 4 screw installation. See 2299001139 Schumacher Positive Negative Clamp and Cable Set  for a complete install.

U.S. Toyo Fan motor Model USTF120381155T. Fan Motor provides cooling for the unit. 115 volt 120mm X 120mm X 39mm. AC Fan Axial Ball Bearing 115V 112 CFM 41dB. Designed for projects that requires cooling or ventilation; or as a replacement fan for various products. Heavy-duty aluminum Frame. Dual-ball bearings for long life. Lifespan of 67,000 hours. Fan can be laid flat or stand upright. Dimensions: 120 x 120 x 38 mm. Airflow at max speed 110 CFM. Noise at 47 dBA. Dual Ball Bearing.

0099000178 Schumacher 3.5" CCW Fan Blade

0099000201 Axle Rod 3/8 X 14.25" Zinc Plated

6" Front foot for new style battery chargers

0099000208 Axle 3/8" X 14.5" With Swage

8" Front foot for new style battery chargers. 3.7" Tall, 2.72" hole centers for screws.

0099000226 Rubber Wheel, 6" Plastic 3/8" Axle

0099000228 Axle, 14.5 X 3/8 With Swage

0099000229 Foot, Plastic

This Knob is for timers on PS Series chargers only with a 1/2 Shaft, there are separate knobs for selector switches with a 3/4 shaft. Please check your part numbers carefully.

This Knob is for selector switches with a 3/4 Shaft only, there are separate knobs for timers with a half shaft. Please check your part numbers carefully.

0099000349 Schumacher Rubber Cover DC Source

Fan Motor provides cooling for the unit. 5 volt quiet design keeps noise to a minimum. 40mm X 40mm X 20mm, 5 volts DC with Connector.

0099000471 Wheel 7" X 1.75" hub thickness x 1/4" offset brick tread for 3/8 Axle. See 2199700006 for Axle end cap.

0099000472 Schumacher Battery Charger Axle 15-5/8" 3/8 Dia. With Cotter Pin Holes

0099000474 Wheel Hub Cap For Wheel (Sold Each)

0099000494 Schumacher DC Adapter Shell, See 2299002203 for complete assembly.

0099000531 Schumacher Halogen Lamp Housing

0099000598 Sears DieHard 1150 Inflator Accessory Kit (This is not the air hose assembly only the inflator for small toys)

Air Compressor Accessory Tip Kit. Includes 3 tips for inflating your beach balls, mattresses, and sports equipment. One of the tips is a needle inflator tip.

0099000679 Schumacher Power Cord Socket

0099000709 Wheel 8" Units 3/8" Axle

0099000719 Schumacher Rubber Bumper (2 Battery Unit). See 5199001142 Screw & 2100110103 washer.

0099001191 Schumacher Cooling Fan 40mm x 40mm x 10mm 12 Volt DC. Fan provides cooling for the unit. Quiet design keeps noise to a minimum.

0400000034 Schumacher Switch SPDT-CO Momentary Off-On

0400000036 Schumacher SPDT Rocker Switch

0400000037 Schumacher 3 Position Rocker Switch On-Off-On DPDT

Single Pole Double Throw Relay 12 Volt coil 30 Amp contacts Panel Mount with quick connect terminals.

Single Pole Double Throw Relay 6 Volt coil 30 Amp contacts Panel Mount with quick connect terminals.

6 Position Rotary Selector Switch (5 Terminals). Older Units used this switch and can be identified by the difference in cabinet mounting, this switch uses a threaded collar with jam nut to mount to case.

7 Position Rotary Selector Switch

Schumacher 2 Position Momentary Rocker Switch

2 Position Slide Selector Switch DPDT Contacts, 6 amp 125VAC Rating (6 Pins)

3 Position Slide Selector Switch (4 pins)

3 Position Slide Selector Switch. 8 pins. 13 amp 125 volt rating. Has removable jumper between pins 3 and 6. 1.40" hole centers.

2 Position Slide Selector Switch Single Pole Double Throw Contacts 6amp 125VAC Rating (3 Pins)

Schumacher 2 Position Mini Rocker Switch, Single Pole Double Throw 3 Terminal

Mini Rocker Selector Switch. SPDT Center Off (on-off-on) 15amp 115 volt 3/16" Terminals

0499000036 Schumacher 2 Position Rocker Switch (6 Terminal)

0499000050 Schumacher Rocker Switch 2 Position Switch 3 Terminal On-On

0499000051 Schumacher 6 Position Rotary Selector Switch With Knob (7 Terminals With Trace). Uses Newer "Twist Lock" Mounting System For newer units. If your unit has an older threaded shoulder with a Pal Nut, use the 0499000022 version of this switch.

0499000052 Schumacher 3 Position Rocker Switch SPDT On-Off-On 16 amp 1/4 spade terminals.

0499000053 Schumacher 2 Position (DPDT) On-On Rocker Switch

6 Position Rotary Selector Switch, 7 wire new style.

2 Position Slide Selector Switch DPDT Contacts, 11 amp 125VAC Rating (6 Pins)

0499000064 Schumacher Switch DPDT with IO Marking

Schumacher 3 Position Slide Switch, Double row contacts (8 pins). 13 Amp 125 VAC. 6.5 Amp 250 VAC. See 0499000031 and remove jumper.

4 Position Rotary Switch with hard wire push in connections. (Works with solid or stranded wire, see notes)

0499000075 Rotary Switch 6 Position

0499000076 7 Position Rotary Switch

0499000080 Schumacher 2 Position Slide Switch (6 Pin)

0499000084 Schumacher Switch 1 Amp 125V AC Momentary Action Red Push Button

0499000086 Schumacher 2 Position Switch

0499000089 Schumacher Selector Switch On/Off Black Knob

0499000091 Schumacher Rotary Switch PSJ-4424. 12 - OFF - 24

0499000092 Schumacher Rotary Switch

0499000110 Rotary Switch 6 Position

0499000117 Schumacher Rocker Switch Red Illuminated

0499000121 Schumacher SPST Switch Lighted 16 Amp

0499000140 Schumacher 2 Position Mini Rocker Switch SPDT 3 Terminal

0499000148 Schumacher Rotary Switch

0499000154 6 Position Rotary Selector Switch

0499000155 Schumacher Spring Coil 13.5mm Long. For 2299002018 Schumacher A/C two prong plug 115 Volt. See 4999000119 A/C Plug Plastic Body for pivot holder.

0600000988 Schumacher Barrier Strip Terminal 8 position 25 Amp with jumpers.

Front Panel Leadset Output Connector With Cap. Includes black and red lead with spade. Easy 4 screw installation. See 2299001139 Schumacher Positive Negative Clamp and Cable Set  for a complete install.

0699000824 Schumacher Terminal Contact Flip Up AC Plug With Bend. See 0499000155 Schumacher Spring Coil 13.5mm Long. For 2299002018 Schumacher A/C two prong plug 115 Volt. See 4999000119 A/C Plug Plastic Body for pivot holder.

0899002882 Schumacher Display Overlay PSJ-2212

0899002883 Schumacher Display Overlay PSJ-4424

0899002892 Schumacher Faceplate PSC-12500A

0899003590 Schumacher Face Plate Label INC-800A

0899003973 Schumacher Faceplate Label

0899004094 Schumacher Faceplate Overlay - Keypad Decal INC-700A

0899007050 Schumacher Faceplate Label SE-82-6-CA

1199003352 Schumacher Foot, Metal, no hardware included.

1199003359 Schumacher Foot, Metal, no hardware included.

1199004366 Schumacher "U" Bracket For 3/8" Axle

1199005112 Schumacher Foot, Metal, no hardware included. For 8" Wheeled units.

2100110103 Schumacher Washer 9.5 X 4.0 X 1.0mm Steel

2100531321 Schumacher Pop Rivet

2100800011 Schumacher Pop Rivet 3/16" X 5/16" Long

214-003-000 Christie Automotive Rectifier Bridge 25 Amp 600 Volt (541103-040)

2199700002 Schumacher Grommet 1/4"

Axle End Cap Fits .375 (3/8") Diameter Axle, Sold as a Pair, Can be used on any 3/8" Axle to secure wheels.

2299000649 Schumacher Heat Sink. Replaces older style 8 diode units. Incorporates a thicker heat sink for better heat dissipation. This item has been discontinued, we do not suggest replacing it with the newer style due to mounting and electrical configuration issues.

2299000679 Schumacher Heatsink Rectifier Assembly

PC Charging Board includes wiring. Requires soldering to install on SCR Heatsink.

PC Charging Board includes wiring. Requires soldering to install on SCR Heatsink.

PC Charging Board includes wiring. Requires soldering to install on SCR Heatsink.

2299000755 Schumacher SCR Heat Sink / Control Board Assembly

PC Charging Board includes wiring. Requires soldering to install on SCR Heatsink.

PC Board SCR Heatsink Assembly

PC Board

2299000810 Schumacher Heat Sink Dual Diode Assembly with male 1/4" spade terminals.

Heat Sink

Heat Sink

Heat Sink SCR Assembly, 12 Amp Rating with SCR's mounted. Some soldering required for installation on circuit board.

PC Charging Board includes wiring. Requires soldering to install on SCR Heatsink. 3 Wires, Black, Green, Grey. Single green LED. (Positive out at the QC terminal)

PC Charging Board includes wiring. Requires soldering to install on SCR Heatsink. Single Black wire / Spade terminal. Single Green LED.

PC Charging Board includes wiring. Requires soldering to install on SCR Heatsink. 3 Wires, Black, Green, Grey. Single green LED.

2299000918 Schumacher PC Charging Board includes wiring. Requires soldering to install on SCR Heatsink. 6 Wires, Grey, Blue, Green, Black, Orange, Green Double Spade.

PC Board

2299000929 Schumacher PC / Resitor Board

PC Charging Board includes wiring. Requires soldering to install on SCR Heatsink.

2299000935 Schumacher PC Board

2299000937 Schumacher PC Charging Board 200.71232

Heatsink Rectifier Assembly, Dual Diode 50 Amp Rating

2299000948 Schumacher Heatsink Rectifier Assembly

Heat Sink Rectifier Assembly, 4 Diode 75 Amp Rating with SCR mounted. Some soldering required for installation on circuit board. Requires soldering to install on PC Board.

Heat Sink Rectifier Assembly. 2 Diode Design with SCR Mounted. Some soldering required for installation on circuit board.

Heat Sink Rectifier Assembly, 4 Diode 75 Amp Rating with SCR mounted. Some soldering required for installation on circuit board.

Heat Sink Rectifier Assembly, SCR mounted. Some soldering required for installation on circuit board.

Discontinued Heat Sink Rectifier Assembly. 2 Diode Design with SCR Mounted. Some soldering required for installation on circuit board. Individual Diodes can be found here.

Heat Sink Rectifier Assembly. 2 Diode Design.

2299001020 Schumacher Heatsink Rectifier Assembly 1/4" Female Spade Terminals

2299001023 Schumacher Battery Charger Wheels - Handle - Hardware Kit SF8050, SE-2158, SE-3612, SE-4020, SE-4022, SE-5010A, SES-4022, SF-4022

2299001025 Schumacher Battery Charger Wheels - Handle - Hardware Kit For Models SE-9500A

2299001027 Schumacher Battery Charger Wheels - Handle - Hardware Kit For Models 71460, 71465, CT-2762A, SE-6242A, SF-6242A

Heatsink Rectifier Assembly 4 Diode design, requires soldering to install. Check your unit for size and type, there were several versions of this unit, earlier units are no longer available. Caution should be used when installing this product and care taken to insure over heating or shorting does not occur while soldering. This unit does not include insulators, bolts, nuts or any other hardware. Discontinued See 3199100028A 75 Amp 400 Volt Positive Diode (Set Of 4) individual diodes.

Battery Charger Wheels - Handle - Hardware Kit For SE3000, SE6030. Includes 3599000210 Handle, 0099000080 Wheels, 0099000123 Plastic Foot, 0099000066 Axle, 2299001076 Misc Parts Bag (screws etc..)

2299001081 Discontinued Schumacher Heatsink Rectifier Assembly

2299001088 Schumacher Heatsink Rectifier Assembly

Heat Sink Rectifier. Two wire rectifier replaces older 4 wire and 2 stud rectifiers.

Heatsink Bridge Rectifier Assembly

10 Amp Charging Circuit Board Heatsink Assembly for CS810. Can also be used as a project charging assembly. 115 Volt input 12 volt 10 Amp output. See 2299001139 Schumacher Positive Negative Clamp and Cable Set for charging clips.

PC Charging Board includes wiring. Controls charging on several models. Requires soldering to install on SCR Heatsink. This board has 2 LED's Red, Green.

2299001173 Raddital Rectifier Heatsink Kit, 300 Amp Cycle Duty, 70 Amp Continuous Duty, 8 Diode Ceramic Insulated Spider Design.

PC Charging Board includes wire harness and indicator light board. Requires soldering to install on Heatsink SCR Board.

2299001208 Schumacher Touch Pad Control Board

Heatsink Rectifier Circuit Board Assembly completely assembled. No soldering required. Unit comes complete with aluminum heat sink, and circuit board ready to install. Automatic charging board with 2 transformer leads and 2 switch leads and 1 green LED. This unit will not retrofit older Diode style chargers.

New Style Circuit Board Assembly (Some soldering may be required). Automatic charging board with 2 transformer leads and 2 switch leads and 1 green LED. This unit will not retrofit older Diode style chargers.

Heatsink Rectifier Circuit Board Assembly completely assembled. No soldering required. Unit comes complete with aluminum heat sink, and circuit board ready to install. Automatic charging board with 4 transformer leads and 3 switch leads 1 red and 1 green led.

Fan Motor provides cooling for the unit. 80mm x 80mm x 25mm 12volt DC quite design keeps noise to a minimum.

2299001288 Schumacher Heatsink Board Assembly 16 Volt AGM.

Discontinued See individual items 2299001378 Schumacher Battery Charger Wheels - Handle - Hardware Kit For Models PSW-2550, PSW-3060, PSW-61224. 3599000474 Handle, 0099000471 Wheels, 1199005112 Foot, 0099000472 Axle.

2299001401 Schumacher 400 Watt Inverter Assembly

2299001424 Schumacher 260 PSI Compressor With Hose & 1.6" Gauge

2299001465 Schumacher Digital Circuit Board Diehard 71234

2299001483 Schumacher Heatsink Rectifier Diehard 71226 / PSC-12500A

Digital Circuit Board functions as a Voltmeter, Ammeter, Amp Hour Accumulator, and Timer. Great for project units as well.

Schumacher Red Positive Booster Clamp features full power jaws (distributes full power to both jaws), heavy duty construction for durability and long life, solid copper jaws for better conductivity, and a braided internal power crossover strap instead of wire for even power to the jaws. Used on all PSJ Series Booster Packs.

Schumacher Black Negative Booster Clamp features full power jaws (distributes full power to both jaws), heavy duty construction for durability and long life, solid copper jaws for better conductivity, and a braided internal power crossover strap instead of wire for even power to the jaws. Used on all PSJ Series Booster Packs.

12volt DC Fan Speed Controller (Three Wire)

Heatsink Rectifier Assembly 2 Diode design, requires soldering to install. Caution should be used when installing this product and care taken to insure over heating or shorting does not occur while soldering

120 Minute mechanical timer with knob. 120 minute total time. Mechanically controls charging in timed Mode with manual hold mode. Single Pole Single Throw (SPST) Switch rated 15 amperes, finish bell.

2299001552 Schumacher Heatsink Rectifier Assembly

Heatsink Rectifier Assembly, requires no soldering to install. Includes 9" leads. Heavy Duty design for greater reliability. 1/4" spade terminal leads make installation a snap.

Fan Motor provides cooling for the unit. 80mm x 80mm x 25mm 12volt DC quite design keeps noise to a minimum. May require the purchase of a 2299001542 Schumacher 12volt DC Fan Speed Controller. Note plug end to determine correct fit. *Please note: You may have to swap plug ends from your old fan.

Heatsink Rectifier Assembly, requires no soldering to install. Used on newer style units. Heavy Duty design for more reliability. 1/4" spade terminal leads make installation a snap. This unit does not include insulators, bolts, nuts or any other hardware.

2299001580 Schumacher Booster Clamp Jaw Kit (distributes full power to both jaws), heavy duty construction for durability and long life, solid copper jaws for better conductivity, and a braided internal power crossover strap instead of wire for even power to the jaws. Used on all PSJ Series Booster Packs.

Heatsink Rectifier Assembly, requires no soldering to install. Includes 9" leads. Used on newer style units. Heavy Duty design for greater reliability. 1/4" spade terminal leads make installation a snap.

2299001593 Schumacher Control Display Board 4 Pin Old Style. Please check your unit for proper fitment before purchasing.

2299001594 Schumacher Power Control Board Heatsink Assembly. 6 Pin Connector new style board with fan controller plug, check your unit for proper fitment before purchasing.

2299001604 Schumacher Control Board PSJ-1812. Controls charging and display status of unit. Works great as a stand alone AGM battery charger as well. just add a 16 volt 500ma power supply (Yellow Leads). Battery Leads (Black - Red), Status Switch leads (Blue)

2299001620 Schumacher Control Board Assembly 85-640 Napa PSC-12500A

Heatsink Rectifier Assembly, requires no soldering to install. Includes 9" leads. Used on newer style units. Heavy Duty design for greater reliability. 1/4" spade terminal leads make installation a snap. *(fan speed control board sold separately)

2299001704 Schumacher Control Board INC-800A

2299001720 Schumacher LCD Display INC-800A

2299001730 Schumacher SCR / Power Board INC-800A

2299001739 Schumacher Fan Motor Assembly INC-800A

2299001744 Schumacher LED-Control Board Display

2299001749 Schumacher INC-812A Fan Control Assembly

2299001750 Schumacher INC-812A Line Filter Board Assembly

INC-812A Transformer / Capacitor Power Board Assembly

2299001752 Schumacher INC-812A Control Display Board

2299001754 Schumacher Control Board Assembly PSW-70300A. This board requires installation and does not include any hardware rivets etc. It is recommended you also purchase 1 of a 240000077 Silicone Heat Transfer Compound 4 gram for proper heat transfer.

Positive Negative Cable Clamp Assembly with SB120A Plug, 4 gauge wire and positive & negative clamps.

2299001776 Schumacher Battery Clamp Assembly INC-800A. SB120 Plug, 4 gauge wire, Heyco bushings installed.

2299001817 Schumacher Control Board Assembly

2299001818 Schumacher Power Board Assembly

2299001849 Schumacher A/C Plug 115 Volt

2299001876 Schumacher Line Filter Assembly

2299001902 Schumacher Cable Plug Set 6ga 6 foot with SB50 Plug. Ring terminal lead and bare wire lead, requires soldering on fuse end of cable.

2299001938 Control Board for INC-4825

(DIscontinued See 0094030008) Schumacher Battery Charger Quick Disconnect, Ring terminal and plug set makes easy access to battery for seasonal charging. Left installed on battery, you can simply plug in and walk away. Designed for permanent connection. Great for hard-to-reach motorcycle batteries.

2299002010 Schumacher USB Power Board

2299002018 Schumacher A/C two prong plug 115 Volt. See 4999000119 A/C Plug Plastic Body for pivot holder.

Fan Motor provides cooling for the unit. 80mm X 80mm X 25mm 12volt DC quite design keeps noise to a minimum. If equipped, check your 2299002070 Schumacher 12volt DC Fan Speed Controller for possible fault as well.

12 Volt DC Dual Fan Motor Control Board. Mounts to the rectifier, fans plug into the board sockets. Requires removal of heat-sink from old board and riveted to this when installing. We recommend the purchase of 240000077 Silicone Heat Transfer Compound for proper heat transfer.

2299002087 Schumacher Display Board PSJ2212 PSJ3612 PSJ4424 (10 Pin Soldered Direct Connect).
*If you have a Power board and display that are soldered together you must replace both items with part numbers 2299002663 Display Board with 10 Pin Plug & 2299002662 3-Amp Power Board with 10 Pin Plug.

2299002088 Schumacher 3-Amp Power Board Display EEJP 12 Volt

2299002090 Schumacher Heat Sink Power Board INC/LVS-36. Leads & LED.

2299002095 Schumacher Control Display Board 6 Pin New Style. Check your unit for proper fitment before purchasing.

Heat Sink Rectifier Assembly. 2 Diode Design with SCR & Circuit board Mounted. No soldering required for installation. Individual Diodes can be found here.

2299002160 Schumacher Power Control Board Only 6 Pin New Style (No Heat Sink). 6 Pin Connector new style board with fan controller plug, check your unit for proper fitment before purchasing. Requires 240000077 Thermal Paste to reinstall board. For complete assembly see 2299001594

2299002203 Schumacher DC Adapter Shell With Board Breaker & Cap

2299002206 Schumacher PC Charging Board XP2260

2299002209 Schumacher 2299000950 Heatsink rectifier with Circuit Board mounted for PS-1022MA

Fan Motor provides cooling for the unit. 80mm X 80mm X 25mm 12volt DC quiet design keeps noise to a minimum. May require the purchase of a 2299001542 Schumacher 12volt DC Fan Speed Controller.

12volt DC Fan Speed Controller (Two Wire New Style)

2299002317 Schumacher D/C Cigarette Lighter Jack With Fiber Board 20 amp fused.

Schumacher Black Negative Booster Clamp features heavy duty construction for durability and long life, solid copper jaws for better conductivity. Heavy duty spring for greater gripping power.

2299002335 Schumacher Control / LED Display Board with 7 pin plug for PSJ2212 PSJ3612 (Old Style). Mounted on the front inside panel.

2299002336 Schumacher 3-Amp Power Board with 7 pin plug (Old Style Units) Provides charging and maintaining of batteries. All boards have a new style plug for the fan. When replacing your power board ensure your fan has the correct plug or you may have to purchase a 0099001191 replacement fan as well. See product details for more info.

2299002338 Schumacher LED Light Board

2299002340 Schumacher USB and LED Control Board

2299002341 Schumacher Power Board 115 Volt For XP750C Jump Starter.

2299002349 Schumacher A/C To D/C Power Board

2299002408 Schumacher PC Power Board Linear Triac Charger. For SE-5212A-CA & XC75W-CA

2299002436 Schumacher LED Display Board PSJ-1812-CA

PC Board Assembly SE-82-6-CA XC6-CA

2299002484 Schumacher PC Power Board Assembly SE-82-6-CA

2299002515 Schumacher PC Board Assembly  SE-5212A-CA SE50

2299002517 Schumacher Display Board

2299002535 Schumacher Control Board Assembly. 85-1500 NAPA, 85-2450 NAPA, SE-4225-CA, SE-4020-CA.

2299002583 Schumacher LED Control Board

2299002628 Schumacher Fan Motor With Resistor XC75CA & XC103CA

2299002633 Schumacher Power Board Rectifier Assembly 200 Amp

Fan Motor provides cooling for the unit. 80mm x 80mm x 25mm 12volt DC quite design keeps noise to a minimum.

2299002645 Power Board Rectifier Assembly 200 Amp with press-fit diodes. (The 3 wires on your old unit may be longer than the replacement board, You may need to splice the wires or use wire nuts to install the board.)

2299002656 Control Board Assembly with LED status display and wires.

2299002662 Schumacher 3-Amp Power Board PSJ2212 PSJ3612 PSJ4424 (10 Pin)

2299002663 Schumacher Display Board PSJ2212 PSJ3612 (10 Pin). Provides charging and maintaining of batteries.

2299002668 Schumacher 3-Amp Power Board PSJ4424 (10 Pin With Relays)

2299002681 Schumacher 12 Volt DC Cigarette Adapter 991220

2299002705 Schumacher 3-Amp Power Board With Relays PSJ-3612 (12 Pin)

2299002706 Schumacher Display Board PSJ-3612 (For 12 Pin Power Boards With Relays). Provides charging and maintaining of batteries.

2299002707 Schumacher 3-Amp Power Board With Relays PSJ4424 (12 Pin)

2299002755 Schumacher Fan Motor With Connector INC-800A. Fan Motor provides cooling for the unit. 120mm x 120mm x 25mm 12 volt 5.40 Watt Sleeve Bearing. DC quite design keeps noise to a minimum.

2299002762 Schumacher Fan Speed Control (Single Fan) For Rivit See 2100800011

2299002834Z Schumacher 115 volt USB Wall Jack to 5 Volt 1 amp output, 12 - 24 Volt DC to 5 Volt USB 1 Amp Car Charger with USB Mini Connector Cord For SL1 & SL360R

2299002868 Schumacher Power Board Rectifier Assembly

Schumacher Red Positive Booster Clamp features heavy duty construction for durability and long life, solid copper jaws for better conductivity. Heavy duty spring for greater gripping power.

SPDT Switch 16 amp Rating Snap-in mount no tools required to install, 1/4 Spade terminals.

246-177-666 Switch 3 Position Rocker SPDT On-Off-On 16 amp 1/4 spade terminals.

246-243-000 Circuit Breaker 12 Volt 50 Amp (578800-050). Universal Breaker replaces many older unit parts.

246-416-666 12 Volt 20 Amp Circuit Breaker

Ammeter Horizontal 0-60 Amp Range features easy snap-in installation, no tools required. Black Charge Rate face. 0-60 Amp range with start. Wire through induction pick-up for greater accuracy.

Power Cord Strain Relief Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord. Securely anchors, insulates, and protects cables at panel entry points.

Power Cord Strain Relief Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord. Securely anchors, insulates, and protects cables at panel entry points.

Power Cord Strain Relief Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord. Securely anchors, insulates, and protects cables at panel entry points. (SR-7P-2).

Power Cord Strain Relief Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord. Securely anchors, insulates, and protects cables at panel entry points.

2999000980 Schumacher Power Control Board Assembly (4 Pin). Requires Thermal Paste to reinstall board.

3100100043 Schumacher Diode

3100300017 Schumacher BTW69-200NS 50 A – 1200 V Non Insulated SCR Thyristor

Fan Blade 6" 4 Blade CW. Same as 130007-001 Christie

50 Amp Diode (Sold Each). Observe correct polarity when installing. Color ring denotes cathode end. Replace all diodes in the same orientation as original diodes.

3199100028 75 Amp 400 Volt Positive Diode (Anode On Lead). Press in diode, used in a wide array of applications. Once installed in the heat-sink these may require soldering to install onto transformer taps.
Use caution when replacing diodes always verify polarity or damage to equipment or self may result. Century Tool & Equipment assumes no responsibility for loss, damage or personal injury due to the miss-application of any electrical component. Purchase of this item agrees to said statement. This item should only be installed by a qualified and experienced electrician.

3199100028A 75 Amp 400 Volt Positive Diode (Anode On Lead). Press in diode, used in a wide array of applications. Once installed in the heat-sink these may require soldering to install onto transformer taps.
Use caution when replacing diodes always verify polarity or damage to equipment or self may result. Century Tool & Equipment assumes no responsibility for loss, damage or personal injury due to the miss-application of any electrical component. Purchase of this item agrees to said statement. This item should only be installed by a qualified and experienced electrician.