| Item | PartNumber | PartDescription | IEEquivalent |
| 1 | | Throttle Handel Assembly | |
| | Outside Trigger | 2950-A1 |
| | Inside Trigger | 2950-A92 |
| 2 | | Grease Fitting | 130SR-188 |
| 3 | 8553 | Oiler Felt | R2-75 |
| 4 | | Oiler Adjusting Screw | R2-71 |
| 5 | | Throttle Valve Plunger | 2950-302 |
| 6 | 8598 | Throttle Valve Assembly | 2934-A50 |
| 7 | 8554 | Throttle Valve Face | 2934-159 |
| 8 | 8555 | Throttle Valve Spring | 834-51 |
| 9 | 8556 | Air Strainer Screen | 434-61 |
| 10 | 8560 | Straight Inlet | 845-565 |
| 11 | 8557 | Reverse Valve Seal | R00BR-210 |
| 12 | | Oil Chamber Plug (2) | ROH-377 |
| 13 | | Trigger | |
| | Outside-type | 844-78 |
| 8752 | Inside-type | 834-93A |
| 14 | | Trigger Pin | |
| | for Outside Trigger | F02-15 |
| | for Inside Trigger | 534-265 |
| 15 | 8574 | Handle Gasket | 805-283 |
| 16 | | Handle Cap Screw (5/16"-18 thread x 1-1/4"Socket Head) (4) | 834-638 |
| 17 | | Handle Cap Screw Washer (4) | 588-140 |
| 18 | | Motor Clamp Washer (2) | MR-207 |
| 19 | 8037 | Rear Rotor Bearing | 834-24 |
| 20 | | Rear End Plate | 2950-12 |
| 21 | | Rotor | 2950-53 |
| 22 | 2161 | Rotor Vane (6) | 2950-42-6 |
| 23 | | Cylinder | 2950-3 |
| 24 | | Front End Plate | 2950-11 |
| 25 | 8575 | Front Rotor Bearing | TA-22A |
| 26 | | Cylinder Dowel | 2950-98 |
| 27 | | Motor Housing Assembly | 2950-A40 |
| 28 | | Reverse Valve Bushing | 2934-3305 |
| 29 | 8579 | Air Port Gasket (2) | R44H-210A |
| 30 | 8350 | Gasket Retainer (2) | 2940-200 |
| 31 | | Reverse Valve Assembly | 2934-A329 |
| 32 | 8283 | Reverse Valve Bushing Seal | 85H-167 |
| 33 | 8850 | Reverse Lever | 2934-658A |
| 34 | 8561 | Reverse Lock Plunger | 4U-663B |
| 35 | 8562 | Plunger Spring | 4U-664 |
| 36 | 8577 | Hammer Case Gasket | 845-36 |
| 37 | | Hammer Frame Assembly | 2950-A703 |
| 38 | | Hammer Pin (2) | 2950-704 |
| 39 | | Hammer (2) | 2950-724 |
| 40 | | Hammer Case Assembly | |
| | for 2950A7 and 2950B7 | 2950-A727 |
| | for 2950A7-EU and 2950B7-EU | 2950-EU-A727 |
| 41 | | Hammer Case Bushing | 2950-541 |
| 42 | | Hammer Case Cap Secrew (3/8"-16 x 1-3/4") SocketHead (Long) (2) | 2945-638 |
| 42A | | Hammer Case Cap Screw (3/8"-16 x 1-1/2") SocketHead (Short) (2) | 844-638 |
| 43 | | Locke Washer (4) | 845-58 |
| 44 | | 1-12" Square Drive Anvil | 2950-726 |
| 45 | | Socket Retaining Ring (for use with square driveanvil | RR100205 |
| 46 | | Spline Drive Anvil Assembly (no. 5 Spline) for2950B1 | VW-1030 |
| 47 | 8143 | Socket Retaining Ball | D04-280 |
| 48 | | Retaining Ball Plunger | 845-230 |
| 49 | 8141 | Plunger Spring | 2940-231 |
| 50 | 8142 | Plunger Retaining Pin | 845-128 |
| 51 | | Dead Handle Bracket | 845-364 |
| 52 | | Dead Handle Bracket Spacer | 845-140 |
| 53 | 8751 | Dead Handle (interchanges with Side Spade HandleAssembly | 834-48 |
| | Side Spade Handle Assembly (interchanges withDead Handle) | 534-A41 |
| 54 | | Side Spade Handle | T15-41 |
| 55 | | Spade Handle Stud | 534-448 |
| 56 | | Stud Nut | 107-73A |
| | Exhaust Deflector Kit | 2934-K23 |
| 57 | 8652 | Exhaust Deflector | 2934-23A |
| 58 | 8656 | Gasket | 2934-223 |
| 59 | 8567 | Silencer | 2940P-311 |
| 60 | | Exhaust Baffle | 2934-124 |
| 61 | | Exhaust Deflector Screw (2) | R43F-104 |
| | Name Plate | 2950-301 |
| | Name Plate Screw | C32-302 |
| | Wooden Box | 2945-96 |
| | Grease Gun | R000A2-228 |
| 9965 | Tune Up Kit (Includes: 3, 7, 9, 11, 15, 19, 22,25, 29 [2], 30 [2], 32, 34, 35, 36) | 2950-TK2 |
