110392 Robinair 1/4" Male Pipe X 1/8" Female Pipe Adapter

112699 Robinair Oil Injector O-Ring

114692 Robinair Oil Bottle Cap for Oil Inject / Drain bottle, for 8 - 12 ounce oil injector bottles. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Don't forget extra bottles (115642) for storing different oil types.

114693 Robinair Oil Bottle Cap (Less Liner With Holes) For Oil Injectors

These gaskets fit 1/4" flare and 1/2 ACME standard hose fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become crushed over time resulting in poor flow or restriction due to swelling. These are standard for some other vendors hoses as well.

12oz. Graduated Oil Drain - Oil Injector Bottle. 12oz Capacity in 1/2oz graduations and 360 Milliliters in 10 Milliliter graduations, for dispensing oil via an injector or for measuring oil removed during refrigerant recovery process. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Don forget extra caps (114692) for storing different oil types.

12oz. Graduated Oil Injector Bottle. 12oz Capacity in 1/2oz graduations and 360 Milliliters in 10 Milliliter graduations. For storing alternative oils for injection & for dispensing oil via an injector or for measuring oil removed during refrigerant recovery process. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Includes cap & Level O-ring.

116368 Robinair Oil Drain Ball Valve

119983 Robinair Half Union 1/8 MPT X Bubble O'Ring

119988 Robinair Low Side Spud

121660 Robinair Cabinet Door Bushing. (See 121678 for screw)

121678 Robinair Cabinet Door Bushing Screw

121771 Robinair 1/8" Male Pipe Thread X 1/8" Pneumatic Union

36" of 1/8" Black Nylon Tube, used to connect low-side and high-side gauge to manifold block and connect oil drain block to drain.

123755 Robinair Door Handle Lockout Plate 17800B. Includes screws and pivot bushing hardware. For Decal See 123939.

123785 Robinair Discharge Oil Coalescing Filter O-Ring

123786 Robinair Discharge Oil Filter Canister O-Ring

123787 Robinair Discharge Oil Coalescing Element separates oil from vapors in the discharge gas stream so it can be returned back to the compressor. This filter can become plugged when a compressor fails from a burn out or overheating due to waxes normally found in refrigerants.

123885 Robinair Condenser Coil With Fittings

123909 Robinair Condenser Outlet Tube Assembly

123919 Robinair Copper Tube Assembly Vapor To Oil Separator

123928 Robinair 1/8" MPT X 1/8" Pneumatic Elbow

123939 Robinair Refrigerant Door Position Decal. Clear decal for indicating door position and hose connection for 17800B units.

123945 Robinair Pressure Temperature Chart Decal

124055 Robinair Float To Inlet Block Filter Tube Assembly. Copper spun filter with tubing and flare nuts, connects the inlet outlet of the float to the inlet block. This filter can become restricted in time and should be replaced as part of regular maintenance.

Robinair’s "High Vacuum Pump Oil" is engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. Laboratory tests prove that Robinair "High Vacuum Pump Oil" is more thermally stable in comparison to other leading brands, which means it resists breaking down due to heat for a longer period of time.

Robinair’s "High Vacuum Pump Oil" is engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. Laboratory tests prove that Robinair "High Vacuum Pump Oil" is more thermally stable in comparison to other leading brands, which means it resists breaking down due to heat for a longer period of time. Robinair "High Vacuum Pump Oil" has a lower moisture content than other oils, thanks to our special packaging and handling procedures. Moisture degrades the oil’s purity, thinning it and reducing the pump’s ability to reach a deep vacuum.

Forward Pumping section for 6 CFM Vacuum Pumps. Includes Pump, Iso Valve Installed, drain fitting and oil fill cap. For model 15600.

Low Side Tank Adapter. 1/2" ACME Female X Lowside Spud used for tank fill and maintenance procedures. 1/2" ACME Female x Low-Side R-134a Coupler

Parts Kit For Manifolds And Hoses Contains an assortment of the most commonly needed replacement parts for repairing manifolds, hoses and various other A/C tools.

8oz. Graduated Oil Drain - Oil Injector Bottle. 8oz Capacity in 1/2oz graduations and 240 Milliliters in 10 Milliliter graduations, for dispensing oil via an injector or for measuring oil removed during refrigernt recovery process.

50lb. R-12 / Universal Gas Refillable Refrigerant Tank. Red Vapor Blue Liquid Ported Valve. 50 lb. capacity refrigerant tank for R-12, R-22, R-502 (universal) with 1/4" Flare fittings

17773 Robinair O-Ring For R-134a Quick Seal Fittings (2 Pack). Fits the internal face of the quickseal fitting on 134A hoses for recovery equipment, gauge set hoses and tank fill hoses with 1/2" ACME fittings.

The 17800C is ideal for refrigerated trailers, buses, RVs, and other vehicles that use more than one refrigerant and have system charges greater than 6 pounds. The 17800B Recovers, Recycles, Evacuates, and Recharges R-12, R-134a, R-22, R-502, R-404, MP and HP Blends and many more! all in one fast, continuous operation through one hook-up.

Lowside Service Coupler 134a. Field service couplers connect to our special Enviro-Guard hoses to allow access to service ports on automotive R-134a A/C systems.

Highside Service Coupler 134a. Field service couplers connect to our special Enviro-Guard hoses to allow access to service ports on automotive R-134a A/C systems.

18192 Robinair High/Low Side Service Couplers 134a. Field service couplers connect to our special Enviro-Guard hoses to allow access to service ports on automotive R-134a A/C systems.

Power Cord - 110 Volt 16 Gauge. For heay duty cord see 551628.

19103 Robinair 12oz Replacement Oil Drain Bottle.

O-Ring Kit For 18190A & 18191A Couplers

96" Red Ball Valve End Hose for High Pressure gases. Ball Valve end prevents gas leakage or loss when removing hoses from their fittings. Safe for use on all refrigerants.

96" Blue Ball Valve End Hose for High Pressure gases. Ball Valve end prevents gas leakage or loss when removing hoses from their fittings. Safe for use on all refrigerants.

19299 Robinair 36" Yellow Quick-Seal Enviro-Guard Tank Hose 1/4" Flare For R-12 and other gasses. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Quick-Seal Fittings prevent pressure release when disconnected form their fittings.

36" Blue Quickseal Hose - Discontinued - See RO19350 R134a blue liquid tank hose. Allows flow from liquid port on tank to unit for charging vehicle.

19307 Robinair 36" Red Double Quick-Seal Enviro-Guard Tank Hose R134A. Enviro-Guard Hoses for Automotive R-134A. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible.

19309 Robinair 96" Blue Double Quick-Seal Enviro-Guard Hose 1/4" Flare. Enviro-Guard Hoses for Automotive R-12and other gases. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction.  740 psi working pressure, 3700 psi burst pressure.

19310 Robinair 36" Yellow Double Quick-Seal Enviro-Guard Tank Hose 1/4" Flare. Enviro-Guard Hoses for Automotive R-12. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

19311 Robinair 36" Blue Double Quick-Seal Enviro-Guard Tank Hose 1/4" Flare. Enviro-Guard Hoses for Automotive R-12 and other gasses. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

19312 Robinair 36" Red Double Quick-Seal Enviro-Guard Tank Hose 1/4" Flare. Enviro-Guard Hoses for Automotive R-12. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. 740 psi working pressure, 3700 psi burst pressure.

19313 Robinair 36" Yellow Double Quick-Seal Enviro-Guard Tank Hose R134A. Enviro-Guard Hoses for Automotive R-134A. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible.

96" High Side System Hose R134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible.

96" Low Side System Hose R134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible.

19652 Robinair Oil-Less Compressor For 25150A 25175A 25200B 17800B (Special order item)

The 19776 filter-drier has been specifically formulated using XH9 drier desicant to trap acid and particulates and is formulated to remove water from the refrigerant. You must change the filter-drier to assure adequate moisture and contaminant removal.

10 In. Pneumatic Wheel 5/8" Axle For Sidewinder Style Units. Deep tread design for no slip traction even on wet or oily floors. A tubeless design with long air stems provide easy inflation.

214802 Robinair 1/4" Pipe Tee

50lb. R-134a Refillable Refrigerant Tank. Red Vapor Blue Liquid Ported Valve and a third port for vapor/air purge (a must for 3 hose recovery units). 50 lb. capacity refrigerant tank for R-134a with 1/2" ACME fittings. Fits models 12134, 34700, 17534, 17800 series

These gaskets fit 1/4" flare and 1/2 ACME standard fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become smashed over time resulting in poor flow.

523568 Robinair 1/4" MPT X 1/4" Compression Union

539668 Robinair Suction Accumulator Canister O-Ring

551628 PROMAX Power Cord 115 Volt 14 Gauge

Main Power Switch Controls the power between the power cord and the main board.

Blue 240" Enviro-Guard Hose for Automotive R-134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant, yet remains flexible. Meet all specifications for low permeation construction. Clearly marked for R-134a. 740 psi working pressure, 3700 psi burst pressure.

Set of Red/Blue 20’ Enviro-Guard Hoses for Automotive R-134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant.

Fan Used to keep the unit hermetic compressor and electrical components cool.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Fan Used to force air through the evaporator/condenser.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Robinair Keypad 17700 34700 (See RA19253 For New Style Keypad/Decal) - Sends controlling signals to program the main board.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Solenoid Rebuild Kit Normally closed Solenoid Rebuild Kit - Used to rebuild certain solenoids in manifolds or discrete (RA19006) etc..
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

120 Volt 25 Watt Heater Band. Heat is applied to the system oil separator to assist in vaporizing the refrigerant before entering the compressor. Includes Heater Band, Thermal Insulation wrap, Foil Tape, 1/4" Female Faston Wire connectors. Fits 4" Diameter Vessels. +/- 1/4".
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Air Purge Gauge Used to monitor refrigerant tank pressure. Correlate with PT chart to monitor air percentage. Discontinued See RA19787
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Air Purge Gauge Used to monitor refrigerant tank pressure. Correlate with PT chart to monitor air percentage. Discontinued See RA19787
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

36" Blue Quickseal Hose - Discontinued - See RO19372 R12 blue liquid tank hose. Allows flow from liquid port on tank to unit for charging vehicle.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

This 1/4" Flare Oil Injector Assembly Allows for the storage 8 ounces and injection of oils and dyes into the A/C system with out permitting air to enter into the system. It attaches directly to the inlet fitting of any recovery unit and can be left permanently installed. Features full flow of refrigerant and will not impede charging or recovery.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Check Valve, This kit includes 1 check valve & O-ring. Allows flow in one direction only, towards the recovery solenoid, and prevents refrigerant from escaping out of the inlet after recovery and during recycling, evacuation and shutdown.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Main Power Switch Controls the power between the power cord and the main board.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Pressure Switch If pressure inside the unit exceeds 435psi, the switch opens, stopping all functions of unit. NOTE: Switch opens at 435psi +/- 10psi and resets at 320psi +/- 20psi.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

The internal fittings used in the manifold block style machines use o-ring bubble fittings instead of flare fittings and require o-ring replacements to seal properly. (10 Pack)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115v Solenoid Coil Coil only, used to energize a normally closed solenoid that, when energized, allows flow. i.e. Recovery, Charge, vacuum, etc. NOTE: RA19258 Solenoid Rebuild Kit
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Tank Strap Single Used to keep the tank in place when positioning the unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Panel mount manifold Valve Assembly. High and Low side Manual valves that control the flow of refrigerant into the unit. Valves measure 3.5" on center.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Side Gauge ACR2000 - Used to monitor the discharge pressure of the vehicle being serviced. Discontinued See RA19787
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA19614 Low Side 134A Gauge With Indicator Lens ACR2000 - Used to monitor the suction pressure of the vehicle being serviced. Includes mounting hardware and instructions.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Oil Drain Switch, 1/8 Male Pipe thread, Used to control solenoid operation from accumulator to waste oil bottle. Allows unit to dump waste oil recovered from vehicle. NOTE: Opens solenoid at 16psi and closes at 9psi.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Breaker 7 Amp Protects the unit from drawing too much current. If tripped, unit is completely inoperative.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Scale 17800B Series Sends a signal to the main board for accurate weight readings during charging and recovery (strain gauge style).
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Compressor 1/2 Hp 17800B Pumps the refrigerant from vehicle being serviced into the ISV or tank, on or inside of unit, for storage.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Check Valve 1/8 Male Pipe Thread X 1/2 Male Acme. Stops the refrigerant from flowing in the opposite direction during the clearing process.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

3/8" O-Ring (10 Pack)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Side Gauge - Generic Used to monitor the discharge pressure of the vehicle being serviced. 1/8" female pipe connection back tap. 0-500 PSI Range, PSI, Kpa, Bar Pressure Scales On Face. Includes Mounting Hardware and Instructions.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Fuse 1/2 Amp .197" X .788" A protection device used to protect the unit against excessive current.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Float Chamber 17800B Magnetic float switch that sends a signal to the main circuit board when liquid is entering the system. The RA19804 Series bottle switch is a compact, economical liquid level sensing device for external mounting in applications not suited to small, internally-mounted level switches. These single point devices are typically used for low or high level sensing. 1/4" NPT Inlet (Bottle) 1/8" NPT Outlet (Cap).
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Dual bulb thermostatic expansion valve controls flow of refrigerant to the inlet and outlet of the suction accumulator of the unit. Unique design uses two sample bulbs to control the amount of liquid refrigerant that enters the coaxial coil.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA20081 Robinair Compressor 115 Volt (New Style 17800B). Replaces older style compressors, requires new start components (RA20084) and tubing kit (RA20083) to install. Includes mounting hardware & instructions.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA20132 Robinair Condenser Coil With Fittings
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.