110138 Robinair Tinnerman Clips Speednut Bracket - 90 Degree. (5 Pack) for Upper Gray Shroud For Cart Style Recovery Units.

These gaskets fit 1/4" flare and 1/2 ACME standard hose fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become crushed over time resulting in poor flow or restriction due to swelling. These are standard for some other vendors hoses as well.

Contains one quick change filter-drier to be used on both R-12 and R-134a stations, and one 16 ounce bottle of our Premium High Vacuum Pump Oil. For early models using 34430 Filter-Drier (17700A, 34700, 34300-2K). See your instruction manual if you have questions about which filter-drier to use.

Keep recovery and recycling units operating at peak efficiency with a convenient maintenance kit. Contains one quick change filter-drier to be used on either R-12 or R-134a stations, and one 16 ounce bottle of our Premium High Vacuum Pump Oil.  Designed for newer units manufactured after 1998.

Robinair’s "High Vacuum Pump Oil" is engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. Laboratory tests prove that Robinair "High Vacuum Pump Oil" is more thermally stable in comparison to other leading brands, which means it resists breaking down due to heat for a longer period of time.

Robinair’s "High Vacuum Pump Oil" is engineered to maintain maximum viscosity at high running temperatures and to improve cold weather starts. Laboratory tests prove that Robinair "High Vacuum Pump Oil" is more thermally stable in comparison to other leading brands, which means it resists breaking down due to heat for a longer period of time. Robinair "High Vacuum Pump Oil" has a lower moisture content than other oils, thanks to our special packaging and handling procedures. Moisture degrades the oil’s purity, thinning it and reducing the pump’s ability to reach a deep vacuum.

8oz. Graduated Oil Drain - Oil Injector Bottle. 8oz Capacity in 1/2oz graduations and 240 Milliliters in 10 Milliliter graduations, for dispensing oil via an injector or for measuring oil removed during refrigernt recovery process.

This Metering Tank Adapter allows gas to be recovered via the liquid port of a virgin refrigerant cylinder with a low side coupler for faster filling of your internal cylinder. The brass fitting is metered with a small orifice to prevent refrigerant flooding preventing damage to the recovery units compressor. Required for some units.

19740 Source Tank Filter For 134A units. Protect your investment from debris and harmful elements from tank manufacturing processes. Metal debris can foul solenoids causing unnecessary repairs and equipment failures. Install this filter on the hose end of your tank add hose to protect your machine. 100 mesh screen is replaceable or cleanable. 1/2" Female ACME X 1/2" Male ACME fittings Installs inline of tank fill hose.

Lower Gray Shroud For Cart Style Recovery Units. Replaces all other color shrouds.

The Robinair 34430 filter-drier has been specifically formulated using XH9 drier desiccant to trap acid and particulates and is formulated to remove water from the refrigerant. You must regularly change the 34430 filter-drier to assure adequate moisture and contaminant removal.

The 34724 Robinair filter drier has been specifically formulated to trap acid and particulates and is formulated to remove water from the refrigerant. DO NOT accept look alike or knock off filters. You must change the filter-drier to assure adequate moisture and contaminant removal. Typically, you can recycle up to 300 pounds (136 kilograms) of R-134a or 600 pounds (272 kilograms) of refrigerant between filter changes (depending on your model). To help you know when you’ve reached that point, the unit displays the warning message prompting you to change the filter drier.

These gaskets fit 1/4" flare and 1/2 ACME standard fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become smashed over time resulting in poor flow.

557648 Robinair 34724 Filter O-Ring Small

557649 Robinair 34724 Filter O-Ring Large

Main Power Switch Controls the power between the power cord and the main board.

Set of Red/Blue 20’ Enviro-Guard Hoses for Automotive R-134A. Enviro-Guard Hoses for Automotive R-134a. Enviro-Guard Hoses are constructed of special barrier material which prevent virtually any permeation of refrigerant.

1/4 Flare Seal Cap with anchor retention strap prevents loss when not in use.

Recent production changes may affect your placement of this pump. The new pump was designed for 17800B cart style Recovery Recycling Units Only. For all other applications See 15548 For Replacement pumping section or RA19902 as a possible replacement.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Fan Used to keep the unit hermetic compressor and electrical components cool.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

System Relay 115 volt coil, double pole single throw normally open switch with dual sets of 15 amp contacts. Acts as a pilot from the circuit board usually carrying higher amp loads to protect smaller relays on board. Can be used for universal applications due to the high amp contact rating.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Breaker 3 Amp Protects the unit from drawing too much current. If tripped, controller is inoperative.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Ball Valve Assembly A manual valve that, when open, routes discharge pressure through the condenser.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115 Volt Grounded recepticle that acessories plug into
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Pressure Cutout 17650 / 17655 A normally closed sensor that opens, stopping the recovery process when the compressor discharge pressure reaches 435 psi. SPDT Contact arrangement. 1/4 spade termination.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA19181 Robinair 115 Volt Power Cord Receptacle
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Solenoid Rebuild Kit Normally closed Solenoid Rebuild Kit - Used to rebuild certain solenoids in manifolds or discrete (RA19006) etc..
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Main Power Switch Controls the power between the power cord and the main board.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Side Gauge Reads pressure entering the high side hose.Panel mount & nuts included. 1/8" Female Pipe Thread connection. See RA19257 2-3/4" Replacement Gauge Lens.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115v 100CFM Fan Cooling fan positioned to pull air into front of unit across condenser and compressor and discharge it through top of unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Vacuum Pump Protection Switch Normally open switch closes at 25psi and reopens at 10psi. Prevents vacuum pump from starting when pressure exists in vehicle's system.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

110v Compressor With O-Ring Fittings - Discontinued - See RA19865
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Solar Power Tank Thermometer (F/C) Used to monitor tank temperature. Use with PT chart to determine air percentage. You will also need a 523568 compression fitting to finish the install.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

110v N/C Skinner Valve
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Scale Assembly Single Sends a signal to the main board for accurate weight readings and tank overfill protection.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

The internal fittings used in the manifold block style machines use o-ring bubble fittings instead of flare fittings and require o-ring replacements to seal properly. (10 Pack)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115v Solenoid Coil Coil only, used to energize a normally closed solenoid that, when energized, allows flow. i.e. Recovery, Charge, vacuum, etc. NOTE: RA19258 Solenoid Rebuild Kit
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Check Valve 1/8 M Pipe X 1/4 Flare O-Ring A two port valve, that normally allows fluid (liquid or gas) to flow through it in only one direction.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Keypad 34234 User input device attached to a circuit board to select start, stop, and program functions of the unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Circuit Board AC890 User interface for controlling refrigerant recovery, recycling, recharging, and other functions of the unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Circuit Board 343002K User interface for controlling refrigerant recovery, recycling, recharging, and other functions of the unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Keypad 343002K User input device attached to a circuit board to select start, stop, and program functions of the unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115 Volt Cubigel Compressor (Replaces The RA17110, RA17434, RA19458, & RA19748) Includes all hardware and electrical for a complete install. See additional plumbing retrofit kits noted for older style units.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Fastener Seal and hardware kit for Robinair recovery units is a service provider must have. This kit contains 38 of the most requested hardware and small maintenance items on most Robinair machines many of which are difficult or impossible to find by themselves, including gaskets seals, bolts and screws, pneumatic fittings, door latches, Torx screws, flare gaskets and other hard to find or specific related items. 3/8 Hose Gasket, 1/4 Fl Copper gasket, O'Rings, Screws Torx, Speed Nuts, Tinnerman U Clip, 1/2 Acme Jam nut, Pneumatic Fittings, Pan Head screws, Grommets, Door Latch Receptacle, Connector, Plastite connector, Bezel 7002K / 700Z, Door Latch Spring, Injector Bulkhead Fitting, Oil Injector Cap And Bulkhead Fitting, Vacuum Pump Fill Caps, Shreader Cores. Housed in a Double sided flip top case with extra space for other items.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.