8' 6AWG Welding Wire Lead Set with heavy duty polished clamps featuring coated clamp handles. a 50 lb. Jaw Strength provides positive connections and color coded wires make for easy identification. These even have molded strain relief built on the cables. Ring terminal connections make installation a snap.

246-408-000 6 Position Rotary Selector Switch (No Knob). This switch has been modified from the original metal stem design to a plastic stem and the pin locations have changed. Switch should be wired number to number not by tab location.

246-408-666 Rotary Selector Switch 6 Position With Knob. This switch has been modified from the original metal stem design to a plastic stem and the pin locations have changed. Switch should be wired number to number not by tab location. Includes instructions.

SLA90 Circuit Breaker, Open construction, automatic reset, 90 Amp, no terminal Hardware

246-513-666 Timer Knob (Slotted) Special knob with slotted shoulders for controls with shaft pins.

Test Switch DPDT Momentary 1/4 Spade. OEM Part Every Time

Mechanical Timer controls charging in timed Mode. Single Pole Single Throw (SPST) Switch rated 15 amperes. 120 minute total time with finish bell, two spade terminal connections.

Ammeter Horizontal 0-60 Amp Range features easy snap-in installation, no tools required. Black Charge Rate face. 0-60 Amp range with start. Wire through induction pick-up for greater accuracy.

Power Cord with Current limiting circuit board and leads, Replaces older style boards with resistors

412-749-666 Battery Charger Front Foot

412-751-666 Chrome Battery Charger Handle. Replaces 442-020-166 and other older Century / Solar Handles

413-115-666 Wheels Axle Hub Set. 3/8" OD axle x 13-1/4" long.

442-020-166 Century Battery Charger Handle. Flat side black painted finish.

51-236 Goodall 250 Amp Heatsink Rectifier Kit 60 Amp Continuous Duty, 12 Diode Daisy Wheel Design. Extra Long center studs for thick transformer lead wires.

512-127-000 Rectifier Insulator Standoff. Connects to the back wall of the charger chassis to provide a mount for the rectifier.

Quad Force Rectifier Installation Kit, 200 Amp Cycle Duty, 60 Amp Continuous Duty, 8 Diode Ceramic Insulated Spider Design. Replaces Older Daisy Wheel Design.

Quad Force Rectifier Installation Kit, 250 Amp Cycle Duty, 60 Amp Continuous Duty, 8 Diode Ceramic Insulated Spider Design. Replaces Older Daisy Wheel Design. Heavier heatsink provides better heat dissipation for faster recovery during engine start. Longer life.

865-682-666 Heatsink Rectifier.  Product as pictured.  Does not include any mounting hardware (512-127-000).

865-926-666 Century Rectifier 250 Amp 12 Diode 60 Amp Continuous Duty. Fits Most Older Century & Solar Models

865-932-666 Voltmeter 0-20 Volt Range Horizontal With Board for volt test

G246-408-666 Switch Rotary 6 Position. For Dayton Chargers Only.

S29420-24 Century Battery Charger Clamp Holder With Screws. Now you can stow your clamps in a safe place that doesn't get in the way, drag the ground or short out. Fits any round or flat bar battery charger handle. If using as a universal fit drilling two holes will be necessary.

TJ1-120MB Universal Mechanical 2 Hour Timer With Finish Bell. Mechanically controls charging in timed Mode, has "Hold" for manual un-timed charging. Single Pole Single Throw (SPST) Switch rated 15 amperes. Termination is designed to accept 1/4" Quick Disconnect terminals. Includes mounting screws. Replaces many older mechanical timers.