100122 PROMAX Provax Black Knob
100123 PROMAX Provax Blue Knob
100124 PROMAX Provax Red Knob
1/4" Flare Filter for ProMax and MiniMax Units Designed to protect recovery systems from debris and deposits that would normally harm your unit. Large filter capacity provides long life. All steel construction with enamel finish resists corrosion and rusting.
100345 PROMAX Hose, Blue, 4" Long
These gaskets fit 1/4" flare and 1/2 ACME standard hose fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become crushed over time resulting in poor flow or restriction due to swelling. These are standard for some other vendors hoses as well.
50lb. R-12 / Universal Gas Refillable Refrigerant Tank. Red Vapor Blue Liquid Ported Valve. 50 lb. capacity refrigerant tank for R-12, R-22, R-502 (universal) with 1/4" Flare fittings
These gaskets fit 1/4" flare and 1/2 ACME standard fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become smashed over time resulting in poor flow.
Inlet Block / Manifold Assembly includes black machined block, valves and new knobs. (Caution! Do turn knobs from there original position before installing or they will lose there indexing and improper flow will result)
CP1304 PROMAX Piston
CP1305 PROMAX Connecting Rod (CP1300)
Offset Motor Pump Coupler. Includes coupling, set screw, cap screws, dowel pin.
CP1319 PROMAX Crank Shaft (CP1300)
CP1320 PROMAX Compressor (Replaces CP1300 Except RG3305)
CP1321 PROMAX Connecting Rod (CP1320) less any hardware, you will need bearings, piston, screw, bushings and wrist pin to complete the assembly.
CP1322 PROMAX Crank Shaft (CP1320)
CP1392 PROMAX Piston Cylinder
Valve Plate, no valves or springs. When purchasing this it is customary to purchase the rebuild kit as well, found here.
CRXTOSP1 Tank Overfill Protection Cable Shorting Plug allows the user to override the tank float safety device on most recovery units using a 3 pin brad Harrison cable. Screws in place at the cable end allowing the unit to start. (Always use a scale for accuracy when using this device) 30 & 50 pound tanks should never be filled to a level beyond 80% of tank capacity.
EL1309 PROMAX Momentary Switch
EL1310 PROMAX On/Off Switch
EL1412 PROMAX Capacitor
EL1500 PROMAX Relay DPDT 120VAC 30A
Axial Fan 115 volt, .43 amp 35 watt Rotary Fan, 6.375" Mounting Hole Centers. Two wire lead set for power connection 14" & 24"with 1/4" spade terminals.
This PROMAX piston seal replacement kit is to be used on the old style (round cylinder) and new style (rectangle Cylinder) compressors on RG54xx series, MiniMax Series and PROVAC Compressors.
PROMAX Valve Replacement Kit is to be used on the old style (round cylinder) and new style (rectangle Cylinder) compressors on RG5410 series, MiniMax Series and PROVAC Compressors. Kit includes all necessary parts to rebuild damaged valves and seals.
This PROMAX piston compressor rebuild kit includes all parts needed to rebuild the new style (Rectangle Cylinder Only) compressors on RG54XX series, MiniMax Series and PROVAC Compressors. Kit includes all necessary parts to rebuild the piston "SLYD" Rings, Square piston seal and cylinder seat seals, as well as all necessary parts to rebuild damaged valves and seals and finally the bearings and shaft seal. This Kit does not include the actual valve plate, we suggest the purchase of the valve plate itself here. This kit will not repair round cylinder compressors.
Shaft Seal Replacement Kit for CP1320 Compressor. Includes bearings, seals and o-rings and illustrated instructions.
NB1102 PROMAX #4-40 Pan Head Cap Screw For Knobs
NB4205 PROMAX Connecting Rod Set Screw
NB5662 PROMAX 1/8" Diameter X 1/2" Dowel Pin
PROMAX WRIST PIN 1/4" DIA X 3/4" For Connecting Rod (CP1320)
1/4 Flare Seal Cap with anchor retention strap prevents loss when not in use.
NB9002 PROMAX E-Ring
Discontinued SB1001 PROMAX 1.25" Needle Bearing for older style compressors
SB1009 PROMAX Crank Shaft Bearing
SB2115 PROMAX Piston Seal O-Ring
SB3005 PROMAX Slide Ring
SB4000 PROMAX Connecting Rod Bronze Bushing 1/4" ID
Shaft Seal (New Compressor) Discontinued See KT3306 Bearing Kit Or KT3308 Seal Kit
SB6001 PROMAX Piston Seal
