026-80062-00 RTI Valve Core Tool R12

026-80192-00 RTI Valve Core Remover

The RTI 026-80212-00 extra length condenser blow gun makes quick work of cleaning dirt and debris from the condenser and radiator.

026-80213-00 RTI Valve Core Tool R134a

026-80216-00 RTI Ford Spring Lock Tool Kit

026-80217-00 RTI Dual O'Ring Tool

026-80218-00 RTI Fin Comb Tool Six-Sided

026-80219-00 RTI Sockets - Pinnacle - Set of 2

026-80292-00 Discontinued See TLVC810 Valve Core Tool R134A 8 Mm And 10 Mm Late Model. Those stubborn 8 mm and 10 mm valve cores on those late model vehicles don’t stand a chance with RTI's heavy-duty 026-80292-00 Valve Core Tool. Its 5-1/4 in. length combined with its 3/4 in. knurled diameter body lets this tool get the job done. The use of a 3/8 in. wrench on the hex of either adds plenty of leverage.

028-80002-01 RTI Oil Syringe 2 oz.

Side Can Tap (R12 / R134a & Respective Oils). Hinged insert design means no pieces to lose. Adapts to R-12, R-134a and their respective oil cans. 1/4” flare and 1/2” ACME ports with Schrader cores installed.

Valve Core Remover / Installer Deep Core R-134A

A reversible wrench with four square openings: ¼" and 3/16" on one end, and 3/8" and 5/16" on the other end. Sizes are stamped near the openings.

Hub Plate Remover / Installer For A6 And R4 Compressor. This compact tool is used both to remove the clutch for access to the shaft seal and to re-install it by simply inverting the nut and main bearing. No. 10861 – A6, R4.

Robinair 115v heater blanket speeds charging by maintaining a constant temperature at the tank, thus creating a positive pressure differential between the refrigerant source and the A/C system.

A reversible ratchet wrench with ½" and 9/16" hex openings on one end and 3/16" and ¼" square openings on the other. For use on A/C system service valves with M51 valve.

11012 Robinair Offset Wrench. This reversible ratchet wrench features 25° bends on each end for greater accessibility, square openings of ¼", 3/16", 3/8" and5/16" are clearly marked. Allows greater access to service valves on smaller more compact systems.

Use the 11145 to magnetize tools in order to keep small screws and nuts in position, especially helpful when working in confined spaces, or demagnetize tools when working on or near electronic circuit boards. Simply insert a screwdriver or nut driver into the (+) opening, slowly draw it out and it's magnetized. Leave the magnetizer on the tool for extra strength. To demagnetize, slowly draw the tool through the smallest area of the (-) opening. The 11145 is an essential tool for the professional and do-it-yourselfer alike.

Certified by NSF to meet ANSI/NSF Standard 61 for use on potable water. Non-toxic and lead free, the Pipetite Stik is for use for water, steam, air, natural gas, and LP gas. Use on metal threads. Do not use on Oxygen service, use PTFE Tape. Sealing temperature is up to 350° F (177° C) and pressures to 2,000 psi (136 bar) for liquids and 350 psi (24 bar) for gasses.

Patented clamping mechanism quickly and securely pinches off tubing and cloth-reinforced hose. A comfortable cushion grip makes work easy with less hand fatigue. Ideal for closing off compressor process tubes. For 3/16", 1/4", 5/16" and 3/8" tubing.

This kit provides the fastest and easiest means of connecting charging lines to process tubes for evacuation and recharging a system. The design assures an absolute seal between tubing and the charging hose. It eliminates the need for flaring and the possibility of tubing chips getting into the system.

One convenient tool, forms solder cups on six (6) different sizes of tubing. Made of fatigue proof steel
Works on 3/16", 1/4", 5/16", 3/8", 1/2" and 5/8" tubing.

12703 Titan 9pc SAE Folding Hex Key Set: The SAE  hex key set is ready to go to work for you with nine differently sized hex keys.

12708 Titan 7pc Metric Folding Hex Key Set: The Metric hex key set is ready to go to work for you with seven differently sized hex keys.

12712 Titan 25pc Hex Key Set: This set includes both SAE and Metric sizes. Made of heat treated black oxide finished carbon steel for long tool life and durability, in a handy storage holder with pivot style release feature to prevent the moving of other tools to remove one from the holder and it keeps the tool in the holder until you are ready to use it.

12713 Titan 13pc SAE Non Slip Hex Key Set: This hex key set features red coloring for easy identification, extra long 9" arms for maximum torque, a patent pending textured finish and laser etched sizes.

12714 Titan 9pc Metric Non Slip Hex Key Set: This hex key set features blue coloring for easy identification, extra long 9" arms for maximum torque, a patent pending textured finish and laser etched sizes.

12715 Titan 13pc Tamper Resistant Star Key Set: This star key set features green coloring for easy identification, extra long arms for maximum torque, a patent pending textured finish and laser etched sizes.

12718 Titan 13pc SAE Long Arm Hex Key Set: This hex key set features high quality alloy steel, black oxide finish, long arms for more torque in a convenient plastic holder with size markings.

12719 Titan 9pc Metric Long Arm Hex Key Set: This hex key set features high quality alloy steel, black oxide finish, long arms for more torque in a convenient plastic holder with size markings.

12726 Titan 16pc SAE/Metric Hex Key Set

12727 Titan 7pc SAE Short Arm Hex Key Set: This hex key set has a red colored storage container for color coded identification, alloy steel construction with black oxide finish.

12733 Titan 12 Point 8-Piece Extra Long XZN Triple-Square Key Set. Constructed of durable, high-quality S2 steel with a satin-plated textured finish for non-slip grip. Fits many fasteners found on imports including VW, Audi, BMW, and Porsche. Sizes are laser etched onto color-coded L-keys for quick and easy identification and set includes a plastic organizer with size markings. Set includes: M3, M4, M5, M6, M8, M9, M10, M12 extra-long precision keys.

12734 Titan 10pc Tamper Resistant 5-Lobe Key Set

12735 Titan 9pc Detent Ball SAE Hex Key Set: The SAE ball end hex key set is ready to go to work for you with nine differently sized hex keys and ball ends for those odd angles we sometimes run into.

12736 Titan 9pc Detent Ball Metric Hex Key Set: The SAE ball end hex key set is ready to go to work for you with nine differently sized hex keys and ball ends for those odd angles we sometimes run into.

12737 Titan 13 Piece SAE Low Profile Hex Key Set. Low-profile design allows for higher torque application and better access in confined areas. Constructed of S2 Alloy steel. Rust resistant satin finish. Handy storage rack with hanger. Sizes: 0.05, 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 3/16, 7/32, 1/4, 5/16 and 3/8"

12739 Titan 39pc Star & Hex Key Set: With this set you will get 12 SAE hex keys, 13 Metric hex keys and 14 Star keys all of which have long arm design and are organized in a color coded folding storage holder.

12756 Titan 12pc SAE Hex Extractor Set: These are for the removal of stripped or damaged hex head bolts. They have edge cutting tips to extract worn out hex screws without causing any further damage, extra long for maximum leverage, will not damage hex fasteners.

13144 Robinair General Purpose Valve 1/4 MFL X 1/4 FPT Coupler Hand Wheel Shut-Off Valve. Brass valves have a male flare fitting on one end and 1/4" female pipe fitting on the other. Nylon seat with Teflon packing gives a quick, tight seal.

Access Valve Core Remover With 6 Valve Cores

Quickly deburrs aluminum, copper, and steel tubing, and can work on any size tubing. It's made with a high-speed, steel blade and a durable aluminum handle. Three spare blades store in the handle.

The Robinair 14388 Oil-Pump' design allows you to add refrigerant oil to a system under pressure. The pump mounts on a one-gallon container of refrigeration oil and pumps oil directly into the refrigeration system, keeping the oil free of moisture and eliminating the mess.

Compact Electronic Thermistor Vacuum Gauge indicates when system is ready for recharge. Designed for use under high vacuum, reads down to 10 microns

This handy tool makes fast and easy business accessing a refrigeration line not equipped with access fittings. Supplies instant pierce and seal for fast, efficient refrigerant evacuation. Patented clamping mechanism automatically locks on tubing, no adjustment is required. Replacement tips are available.

16390 Robinair Inspection Enclosure.  Indoors it provides darkened area for inspecting engine compartments without inconveniencing other technicians.  Outdoors it speeds testing and inspection by blocking light, wind, and rain.  Provides personal protection during inclement weather and enhances intensity of any UV light.

Receiver- Drier Gaskets For Chrysler Adapter Kit 17556 0r 17595

Aligning Pins  can become worn or damaged over time and should be replaced as part of regular maintainence of your tool. Use these 3 Robinair Aligning Pins to bring your tool back to new spec. For 10204 / 10290 Adjustable Spanner Wrenchs

This straight adapter is designed specifically for General Motors vehicles with R-12 air conditioning systems featuring “Positive Seal” high-side charge valves. The adapter is made of brass with an easy-to-grip coupler nut, 1/4" MFL x 3/16" FFL.

Seal Repair Kit For 14388

Remove valve cores without losing the system charge. Designed specifically for use during evacuation or recharging of any system with valve core-type access ports. Makes replacing leaking valve core under charge a snap. Never recover a system to replace a core again. A huge time saver.

Remove and install the valve core from a 1/4" male flare access fitting without the loss of refrigerant or in situations where Fast evacuation or charge is desired. Schrader core fittings only allow 1.2 CFM flow, removing the core dramatically improves the speed of vacuum and charging.

Remove and install the valve core from a 1/4" male flare access fitting without the loss of refrigerant. Durable, solid brass tool has a ball valve that can be opened and closed in just a quarter-turn, rather than a stem-type valve.

HT212 Bacharach PVC Pipe Cutter 1-5/8" Capacity

Replacement Tip with gaskets and cover guard. 14998 Tube Piercing Pliers makes fast and easy business accessing a refrigeration line not equipped with access fittings. Supplies instant pierce and seal for fast, efficient refrigerant evacuation. Patented clamping mechanism automatically locks on tubing, no adjustment is required.

Fin Comb - Metal: This tool is used to straighten and clean condenser and evaporator fins.

Fin Comb: This fin comb allows one to straighten bent radiator and air conditioning condenser fins to increase air flow and regain the efficiency lost due to the damage to the cooling fins.

R12 Service Port Thread Chaser: This item is used to clean the threads on R12 service ports.

Low Side Bridgeport Socket Adapter (8 Sided) Part # 2746: This socket is designed to work on the 8 sided Bridgport Style Adapters on the Low Side. For High Side Bridgeport Socket Adapter (8 Sided)  See Part # 2748

High Side Bridgeport Socket Adapter (8 Sided) Part # 2748: This socket is designed to work on the 8 sided Bridgport Style Adapters on the High Side For Low Side Bridgeport Socket Adapter (8 Sided)  See Part # 2746

R134a Service Port Deburring Tool: This tool is utilized to remove sharp edges from R134a service ports, helping to prevent R134a service coupler damage.

Thread Chaser - Standard - Set: These SAE thread chasers help save time and money by saving costly replacement when damaged threads are the problem. Works on import and domestic vehicles.

Thread Chaser - Metric - Set: These Metric thread chasers help save time and money by saving costly replacement when damaged threads are the problem. Works on import and domestic vehicles.

Perfect for inspecting hidden areas, the mirror swivels to almost any position. Overall length: 17_.

Insulation Tape: This 30 foot roll of A/C insulation tape sticks to metal or rubber, protects parts from heat and it insulates and seals parts.

9 Piece Spring Lock Assortment Tool Set: This spring lock coupler too set is for opening and closing A/C springlock couplers, fuel line couplers and transmission line couplers.

Universal Clutch Holding Tool (Spanner Wrench): This universal compressor clutch holding tool is designed to help by holding the compressor clutch hub during removal and installation.

Clutch Hub Puller/Installer Tool Kit: This compressor clutch hub puller / installer kit is to be used with GM, Ford, Chrysler and Import vehicles. The kit includes compressor guide and a molded storage / carry case.

Clutch Hub Remover: This clutch hub remover is for A-6 and earlier R4 compressors, and also available in FJC 2925 Clutch Hub Puller / Installer Tool Kit.

Clutch Hub Remover: This clutch hub remover nut and arbor is for Harrison GM DA-6, HR-6 and V5 compressors, and is also available in FJC 2925 Clutch Hub Puller / Installer Tool Kit.

Clutch Hub Remover: This clutch hub remover arbor is for R4 compressors, and is also available in FJC 2925 Clutch Hub Puller / Installer Tool Kit.

Clutch Hub Remover: This clutch hub remover nut and arbor are for Nippondenso, Ford, Chrysler A590, C171,FS-6, FS-6 w/ special 24mm x 2.0, and York / Tecumseh HR980 compressors, and is also available in FJC 2925 Clutch Hub Puller / Installer Tool Kit.

Clutch Hub Remover: This clutch hub remover puller plate and arbor are for Sanden, Zexel / Mitsubishi CH Series compressors, and is also available in FJC 2925 Clutch Hub Puller / Installer Tool Kit.

Clutch Hub Remover: This clutch hub remover arbor is for Zexel / Mitsubishi CH Series compressors, and is also available in FJC 2925 Clutch Hub Puller / Installer Tool Kit.

Clutch Hub Installer: This clutch hub installer Nut & Bearing is for Harrison GM DA-6, HR-6, V5, A-6 & earlier R4, R4, Nippondenso Ford / Chrysler A590, C171 & FS-6, FS-6 w/ special 24mm x 2.0, New Style, York / Tecumseh HR980 compressors, and is also available in FJC 2925 Clutch Hub Puller / Installer Tool Kit.

Clutch Hub Installer: This clutch hub installer arbor is for Harrison GM DA-6, HR-6, V5 and R4 compressors, and is also available in FJC 2925 Clutch Hub Puller / Installer Tool Kit.

Clutch Hub Installer: This clutch hub installer arbor is for A-6 & earlier R4 compressors, and is also available in FJC 2925 Clutch Hub Puller / Installer Tool Kit.

Ford A/C and Fuel Line Spring Lock Coupling Tool.  Ford A/C and Fuel Line Spring Lock Coupling Tool.  Necessary tool releases locking mechanism on all 4 sizes: A (3/4"), B (5/8"), C (1/2") and D (3/8").

Remove and install clutches on GM air conditioning DA6 and V5 compressor clutches without removing retaining ring.

8 pc. A/C, Fuel, Transmission Line, Disconnect Set. Disconnects Fuel, Air Conditioning Transmission Lines with Simple Push-On, Pull-Off Action.

Condenser Fin Comb. 6-in-1 clears and straightens condenser and evaporator coil fins. This item has spacings of 8, 9, 10, 12, 14 and 15 fpi. Small compact screwdriver type, easy to use in confined area.

The 360-80773-00 in-line oil injection assembly for R12 works on most any application. 1/4 flare female on one side and 1/4 flare male on the other. Attaches in-line on either a machine or a gauge set.

The 360-80774-00 Oil injection assembly for R12 or R134a works on most any application. 1/4 flare female on one side and 1/4 flare male on the other. Adapter included to convert to 1/2 ACME for R134a applications. Bracket included for mounting the bottle to the machine.

The 360-81398-00 RTI Total Store A/C Package contains all the accessories and consumables you need to have on hand for A/C service. Includes toolbox with small tools, electronic and UV leak detectors, retrofit adaptors, fin comb, and more.

The 360-81429-00 RTI A/C Tool Kit contains all the tool you need for A/C service.

Easily Disconnects Air Conditioning Lines and Quick Connect Fuel Lines. Set of six tools which disconnect the spring lock couplings on Ford and Chrysler air conditioning line. Also works on fuel line quick connect couplings found on GM, Ford, and Chrysler. The 5/16" size fits on push lock connectors foundon Ford radiators and transmission lines. Easy to use inconfined spaces. Set includes six sizes: 5/16", 3/8", 1/2", 5/8", 3/4" and 7/8".

The 39400 Lisle Angled Disconnect Tool Set disconnects Air Conditioning and Quick Connect Fuel Lines. Connect Fuel Lines. Disconnects spring lock couplings on Ford and Chrysler AC lines. Works on fuel lines and other quick disconnect couplings on domestic and import vehicles. The handles are angled to access tight spots. Made of durable plastic that resists fuels and solvents. Six sizes: 5/16", 3/8", 1/2", 5/8", 3/4" and 7/8". All disconnects available individually skin-packed.

Master Disconnect Set

Seal Gaskets For 40288 / 40330 Tube Piercing Valves (3 Pack)

Line Piercing Valve 1/2" 5/8" OD Tube

Handle Only For 10502 Pulley Installer. Also In 10885 Kit

Works on wide variety of compressor models. Fits clutch hubs that do not have holes that a spanner wrench can grip, or a hex end that a box wrench can grip.
Spreads lubrication to prevent compressor damage at start-up. As recommended by OE compressor manufacturers.

Shaft Seal Installer / Protector For Gm's 4 And 6 Cylinder And Da6 Compressors

LIS42150 Lisle HEX KEY SET 12PC

The 42170 Robinair Mini Split Installation Service Tool Kit is designed to be dedicated specifically for mini-split installation. Features include a single valve manifold gauge, dedicated specifically for Mini-Split installation and service applications. 2 Custom length high pressure hoses, 1 18" ¼" quick seal x ¼" FFL standard blue hose & 1 36" ¼" quick seal x ¼" FFL standard yellow hose, eliminates up to 20% of unnecessary charge volume compared to longer length hoses. Eccentric cone flaring tool produces a rolling action for uniform flare walls, which are ideal for mini-split R410A flares.

LIS42300 Lisle METRIC HEX KEY SET, 9PC.

LIS42500 Lisle LONG ARM HEX KEY SET

LIS42650 Lisle LONG ARM METRIC HEX KEY SET

OTC 4491 Mechanic’s Stethoscope - Quick and accurate way to locate vehicle noise.

51500 Titan AC Fin Comb

51950 Titan 51950 Exo Burr Deburring Tool and External Chamfer Tool. Titan Tools 51950 EXO burr external deburrer and chamfering tool is indispensable in repairing damaged threads. With this deburring tool, you can quickly repair damaged threads from 5/16-inch to 7/8-inch (8-22mm). Hardened HRC 60 steel blades remove burrs and uneven ridges from threaded rods, pipes, and more. Works on hardened and mild steels, grade 8 fasteners, stainless steel, brass, Copper, aluminum, plastics, wood, etc. 1/4-inch hex shank attaches to your drill quickly. Low speeds make this tool most effective – Recommended Speed is 500 RPM in a clockwise direction only.

Remove valve cores without losing the system charge. Designed specifically for use during evacuation or recharging of any system with valve core-type access ports. Makes replacing leaking valve core under charge a snap. Never recover a system to replace a core again. A huge time saver. This tool pays for it self the first time you use it. The tool removes standard R-12 cores as well as most R-134a cores on both Low & High Side Ports. Heavy brass construction with a fine chrome finish prevents corrosion and keeps the tool looking nice as well as easy to clean.

KDT59830 KD Tools 9 pc. Metric Short-Arm Hex Key Set with Caddy

KDT59931 KD Tools 9 pc. Fractional Fold-Up Hex Key Set, Medium

KDT59945 KD Tools 7 pc. Metric Fold-Up Hex Key Set

3/16" And 5/16" Hex Key Adapter

Service Wrench And 60609 3/16" And 5/16" Hex Key Adapter

Color-coded nylon fin combs are designed to easily straighten and clean fins on standard and high efficiency condensers and evaporators. Shape conforms to the hand and thumb for a more comfortable grip. Available individually bagged or as a set of six assorted. 61157 FinFix 7 (21/22 & 23/24 Fins per inch), purple  is for high efficiency units. Made in the USA.

Fin Combs For 14 different fin sizes. Color-coded nylon fin combs are designed to easily straighten and clean fins on standard and high efficiency condensers and evaporators. Shape conforms to the hand and thumb for a more comfortable grip. Available individually bagged or as a set of six assorted. One set of six covers 12 different fin sizes. 61157 is for high efficiency units. Made in the USA.

61164 Ritchie Yellow Jacket FinFix 4 (12 & 14 Fins per inch) Green (25 Count). Color-coded nylon fin combs are designed to easily straighten and clean fins on standard and high efficiency condensers and evaporators. Shape conforms to the hand and thumb for a more comfortable grip. Available individually bagged or as a set of six assorted. Made in the USA.

OTC 6508 Full-Coverage Disconnect Tool Set - If you’re working on Chrysler, Ford, or General Motors vehicles, this set can make your job easier. The tools are designed for heater hoses, transmission oil coolers, air conditioning and fuel lines.

Capillary Tube Cutter

Refrigeration Ratchet Service Wrench Compact chrome satin plated wrench specially designed for use in hard to reach places. 1/4, 3/8, 3/16 and 5/16” square ratchet.

Manual Style Hose Crimper

MKP-745100 Mueller Kueps Wrench Extender. Works with almost any wrench to provide extra torque for loosening difficult nuts. Loosen tight connections in hard to reach areas. Drop forged. Will work on almost any wrench. Extra 1/2" square. 13-1/2" Length

Puller Arbor: Replacement part for FJC Part #s; 7500 - Master Compressor Clutch Puller Kit and 7510 - Compressor Clutch Puller Kit.

Sanden 505 575 Service Set: This tool kit is used to service shaft seals on Sanden 505 and 575 compressors. FJC tool kit Part # 7610 is required.

Universal Pilot: Replacement part for FJC Part # 7500 - Master Compressor Clutch Puller Kit.

Max-Flow™ Deluxe Oil Pump High capacity oil pump; pumps 3.8 oz. per stroke (8-1/2 strokes per quart) Foot stand base provides support and leverage while pumping against high pressures (250 PSI) Fits all size oil containers Can operate unit in reverse with siphon hose accessory 77934, for removing oil from system.

Optional 3/8" Flexible Drain Hose 24" Long Fitting One End Only

2-1/4In. Round Mirror

2-1/4In. Magnifying Mirror

1-1/4In. Round Mirror

1-1/4In. Magnifying Mirror

2In. X 1In. Oval Mirror

Astro 15-piece Master Disconnect kit features a complete set of disconnect tools stored in a handy blow-molded case. Includes a Fuel & Transmission Line Disconnect Set, Oil Cooler Line Remover, and an Air Conditioning & Fuel Line Disconnect Tool Set.

R134A Universal Large Bore Valve Core Remover

R134A Valve Core Remover And Installer. For small core fittings. R-134a Valve Core Remover Installer built with Ball valve design, No need to pump down a system for a simple core change. Controls refrigerant flow with 1/4 turn of the valve lever. Lever position also gives visual indication of whether valve is opened or closed. Solid brass construction High and low side fitting included.

82420 6 pc Flex Torx Key Set 180 degree flex head, Thinner profile vs. traditional fold up key sets, substitute for standard hex bits, black oxide finnish, canvas pouch for compact storage.

Deluxe A/C Service Kit

R134A Can Tap Valve Screw-on design for R134a ACME male can taps. Gasket assures leak proof operation. Built-in safety check valve. Exclusive “full grip” valve knob. 1/2” ACME Male connection.

85510-YF Mastercool R1234YF Piercing Can Tap Valve. 1/2” ACME-LH thread for use with R1234yf Piercing Top designed cans. Exclusive “full grip” valve knob. All metal construction provides durability. Gasket assures leak proof operation. Built-in safety check. Meets SAE J2844.

85512 Mastercool R134A Self Sealing Can Tap Valve Screw-on design for R134a ACME. Gasket assures leak proof operation. Built-in safety check valve. Exclusive “full grip” valve knob. 1/2” ACME Male connection. 1/2” ACME-Male thread for use with R134a self-sealing / reusable cans.

85512-YF Mastercool R1234YF Self Sealing Can Tap Valve. 1/2” ACME-LH thread for use with R1234yf self-sealing/reusable designed cans. Exclusive “full grip” valve knob. All metal construction provides durability. Gasket assures leak proof operation. Built-in safety check. Meets SAE J2844.

Mastercool 85530 3-In-1 Side Mount Can Tap Valve (US Standard) has a unique design that covers 2 7/8” (R134a), 2 1/2” and 2” (OIL) charge cans. Includes 1/2” ACME-M and 1/4”FL-M ports. Internal safety check valve prevents system backflow.

91000-A Mastercool Deluxe Clutch Hub Puller / Installer Kit

Universal Valve Core Tool

Designed for single flare in copper, aluminum, soft steel brake line, and brass tubing (to 45 degrees). Includes five swage adapters 1/8" through 3/4". Chrome swivel, made of alloy steel reduces friction. Forged yoke made of heat-treated steel. Housed in a blow-molded storage case.

R-410A Clutch driven flaring tool with ratchet and case for 3/16", 1/4", 5/16", 3/8", 1/2", 5/8" & 3/4" O.D. tubing. R-410A Eccentrically Type Concentric Flaring Tool engineered specifically to create stronger flare joints for higher pressure R-410A systems. Unique clutch driven feed screw and eccentrically mounted cone produces uniform, clean flare walls without galling. Exclusive 3/8”sq drive incorporated directly in yoke handle for use with ratchet (included). Rugged polyethylene storage case included.

Standard imperial clutch driven flaring tool with ratchet and case for 3/16", 1/4", 5/16", 3/8", 1/2", 5/8" & 3/4" O.D. tubing. Unique clutch driven feed screw and faceted cone produce uniform, clean flare walls without thin spots or galling. Clutch Type Concentric Flaring Tool engineered specifically to create stronger flare joints for higher pressure systems. Provides an exact amount of flaring torque with break away clutch system. Unique clutch driven feed screw and eccentrically mounted cone produces uniform, clean flare walls without galling. Exclusive 3/8”sq drive incorporated directly in yoke handle for use with ratchet (included). Innovative 3/8" square drive incorporated directly in yoke handle for use of ratchet. Rugged polyethylene storage case included.

JB-BACKPACK1 JB Industries JB Backpack

JB-Toolbag1 JB Industries JB Tool Bag

MSKIT1 JB Industries Mini Split Kit 1/4". Includes BACKPACK1 - JB Heavy Duty Tool Back Pack, 22500 - Patriot™ manifold with R-410A gauges, CCLS-60 - 1/4" KOBRA® UL approved Secure Seal hose set, T30605 - Metric (2-8mm) & Imperial (5/64 - 1/4") hex key set, T30600 - Ratcheting eccentric cone flare tool, TRQ1080 - Torque wrench set with 6 spanner heads (10 - 80 N-M), A32525N - 1/4" Female x 1/4" SAE Valve core remover with side port, SHLD-P4 - SHIELD™ locking cap R-410A (4 pack), A31565 - 5/16" Female x 1/4" SAE brass adapters (2 included), NFT5-4 - 1/4" Brass caps (5 included).

MSKIT2 JB Industries Mini Split Back Pack Kit 5/16" Fittings. Includes BACKPACK1 - JB Heavy Duty Tool Back Pack, 22505 - Patriot™ manifold with R-410A gauges, CCLS5-60 - 1/4" KOBRA® UL approved Secure Seal hose set, T30605 - Metric (2-8mm) & Imperial (5/64 - 1/4") hex key set, T30600 - Ratcheting eccentric cone flare tool, TRQ1080 - Torque wrench set with 6 spanner heads (10 - 80 N-M), A32535N - 5/16" Female x 5/16" SAE Valve core remover with side port, SHLD-E4 - SHIELD™ locking cap R-410A (4 pack), A31665 - 5/16" Male x 1/4" Female SAE brass adapters (2 included), NFT5-5 - 5/16" Brass caps (5 included).

MSKIT3 JB Industries Basic Mini Split Kit

The PT200W is a compact, portable instrument for accurately measuring and calculating HVAC/R data such as pressure, Super Heat, Sub Cooling, and temperature differential (tH-tL) that are critical to properly servicing HVAC/R equipment. Use the PT200W as a stand-alone gauge or pair it with a mobile device to set up, store or e mail client and job lists, job site data, invoices and other convenient, time saving features. Pressure range of -14.5 PSIG to 750 PSIG and Temperature Range: 23°F to 149°F, Great for calculating superheat, subcooling, vacuum, temperature and general system performance.

RT175001 JB Industries Torque Spanner Set

RT99017 JB Industries Replacement Clip & Axle For RT70020 RT70021

SCT-1050 JB Industries Side Can Tap - AUTOMOTIVE - Side can tap 1/4" X 1/2" ACME thread fitting. The design of the side can tap allows you to easily adjust from R-12 to 134A refrigerant cylinders for quick and easy charging. Slide handles with proper collar around can and close to pierce. Do not use with any other refrigerants.

The SH-35N Digital Pressure/Temperature Gauge provides a wireless connection to smartphone devices, allowing for system testing without loss of refrigerant—hoses and manifolds not necessary.  The free download of the SH-35N app wirelessly calculates and displays system pressure, temperature, superheat and sub-cooling in an easy-to-read, color format. Sealed touch buttons protect against dirt and dust and includes a carrying case. Test system without losing refrigerant, hoses and manifolds are no longer necessary.

SH-51 JB Industries Digital 28' Temperature Sensor Extension for SH-31N Series - Replacement 28' (8.5 m) temperature sensor extension for use with SH-35N, SH-36N, DM2-3, DM2-5, DM2-8, and DM4-3.

SH-55 JB Industries Carrying Case for SH-31 / SH-31N / SH-34N / SH-35N & TSR-10

SH-56 JB Industries Replacement Wet Socks for SH-35N / SH-36N / DM2-5 / DM2-8 & DM4-3 (5 Pack)

SH-59 JB Industries SH-35N Series 6' Temperature Sensor with Clamp for 1/2" to 7/8" Tubing

3/16'' and 5/16'' hex valve hex key adapter for accessing liquid and suction based valves. Heat treated black oxide played. Made in the USA.

Fin straightener for 8, 9, 10, 12, 14, and 15 spacings per inch.

T21124U JB Industries A.C. & R. Ratchet Wrench - Each - 3/16'', 1/4'' square end and 1/2'', 9/16'' hex port end. Double end reversible ratchet wrench features accurately broached multiple openings and offers the greatest number of uses in a single unit.

3/8'' square end and 1/2'' square end. Double end reversible ratchet wrench features accurately broached multiple openings and offers the great number of uses in a single unit. Made in the USA.

Offset 1/2'', 3/16'' on one end and 3/8'', 5/16'', on other. Double end reversible ratchet wrench features accurately broached multiple openings and offers the greatest number of uses in a single unit. Made in the USA.

T21127U JB Industries Reversible Ratchet Square Service Valve Wrench. 1/4'', 3/16'' on one end and 3/8'', 5/16'' on other end. Double end reversible ratchet wrench features accurately broached multiple openings and offers the greatest number of uses in a single unit. Made in the USA.

This plier-type pinch-off tool temporarily closes off line while making repairs. The quick release trigger and rounded jaws prevent cutting while allowing for reopening and rounding using a standard flare bar. Great for accessing process tubes for charging and resealing, similar to factory seals found on small fractional systems.

T30605 JB Industries Hex Key Set Imperial (5/64" - 1/4") and Metric (2 mm - 8 mm)

The CPS TB04 is an Open side type tubing bender which slips over tube at any point. Makes smooth tight 9/16" radius bends up to 180° with minimum effort and no scoring or flattening of tubing. Calibrated to show angle of bend for accurate tubing placement. Wide hook grips tubing securely.

The CPS TB05 is an Open side type tubing bender which slips over tube at any point. Makes smooth tight radius bends up to 180° with minimum effort and no scoring or flattening of tubing. Calibrated to show angle of bend for accurate tubing placement. Wide hook grips tubing securely. Applicable materials: Soft copper, aluminum, brass, steel, stainless  steel.

The CPS TB06 is an Open side type tubing bender which slips over tube at any point. Makes smooth tight radius bends up to 180° with minimum effort and no scoring or flattening of tubing. Calibrated to show angle of bend for accurate tubing placement. Wide hook grips tubing securely. Applicable materials: Soft copper, aluminum, brass, steel, stainless  steel.

The CPS TB08 is an Open side type tubing bender which slips over tube at any point. Makes smooth tight radius bends up to 180° with minimum effort and no scoring or flattening of tubing. Calibrated to show angle of bend for accurate tubing placement. Wide hook grips tubing securely. Applicable materials: Soft copper, aluminum, brass, steel, stainless  steel.

The CPS TB10 is an Open side type tubing bender which slips over tube at any point. Makes smooth tight radius bends up to 180° with minimum effort and no scoring or flattening of tubing. Calibrated to show angle of bend for accurate tubing placement. Wide hook grips tubing securely. Applicable materials: Soft copper, aluminum, brass, steel, stainless  steel.

The CPS TB12 is an Open side type tubing bender which slips over tube at any point. Makes smooth tight radius bends up to 180° with minimum effort and no scoring or flattening of tubing. Calibrated to show angle of bend for accurate tubing placement. Wide hook grips tubing securely. Applicable materials: Soft copper, aluminum, brass, steel, stainless  steel.

The TB368 is a triple head, all-metal lever type tube bender for 1/4″, 5/16″, 3/8″ (6, 8, 10mm) O.D. soft copper, aluminum and thin wall steel tubing. Creates smooth, tight radius bends up to 90° with minimal effort and without scoring or flattening of the tube. Engraved bend angles are easy to view. Wide hook securely grips tubing.

PRO-SET Premium Mini Tube Cutter. Over-sized turning wheel designed and approved by service technicians for a sure comfortable grip. Can cut tubes as small as 1/8'' (4mm) to as large as 5/8'' (15mm). Small clearance lets this tool work in the smallest spaces - only requires 1-1/4'' for clearance.

PRO-SET premium ratchet feed tube cutter provides consistent clean cuts. Ratchet feed mechanism adjusts fast giving you more cuts in less time. The cutting wheel is forged from top grade steel for easy cutting and longer life. Replacement cutting wheel included in handle. Can cut tubes as small as 3/8'' and as large as 2-5/8''.

PRO-SET premium tube cutter. Top-grade steel cutting wheel provides smooth operation and consistent clean cuts. Fold away steel reamer with turned cutting edge to remove inside burrs; filing surface to remove outside burrs. Can cut tubes as small as 1/8" (4mm) to as large as 1-1/8" (28mm).

PRO-SET Heavy-Duty Tube Cutter. Top-grade steel cutting wheel provides smooth operation and consistent clean cuts. Fold away, steel reamer tool with turned cutting edge removes inside burrs. Filing surface removes outside burrs. Spare Cutting Wheel Located under retractable locking reamer. Use on hard or soft copper, aluminum & brass tubing. Can cut tubes as small as 1/4'' to as large as 1-5/8''.

Combo Pack featuring Mini-Tube Cutter (TC127) and Premium Tube Cutter (TC274). The Mini-Tube Cutter features over-sized turning wheel designed and approved by service technicians for a sure comfortable grip. The Premium Tube Cutter features top-grade steel cutting wheel provides smooth operation and consistent clean cuts, Fold away steel reamer with turned cutting edge to remove inside burrs; filing surface to remove outside burrs.

Ten pack of cutting wheels for CPS TC274 and CPS TC312.

Cutting Wheel and Screw for CPS TC274 and CPS TC312.

Titanium Cutting Wheel and Screw for CPS TC164, CPS TC274 and CPS TC312.

Reamer Blade for CPS TC274 and CPS TC312.

10-Pack of cutting wheel screws for CPS TC274 and CPS TC312.

10-Pack of cutting wheels for TC127.

Cutting Wheel and Screw for CPS TC127.

Titanium Cutting Wheel and Screw for CPS TC127.

Ten pack of screws for CPS TC127 cutting wheel.

Springlock Ford/Import Tool Kit

The TLB410A CPS R-410A Universal A/C Tool & Adapter Kit was designed for the installation and service of Mini-Split & Central A/C systems utilizing R410a refrigerant. The kit includes a 2 valve R410a aluminum manifold with 60" ball valve hoses, a clutch type flaring tool for tube sizes from 3/16" to 3/4", a 6-in1 metric torque wrench set for setting R410a flare nuts to proper torque, a set of imperial and metric hex key sets, a 5/16" valve core removal tool which allows for core replacement under pressure, a complete set of straight and 45 degree swivel flare adapters for access to the units high and low side fittings, 5/16" flare caps for convenience and a free tool bag to carry it all in. Read more here...

The TLB410A CPS R-410A Universal A/C Tool & Adapter Kit was designed for the installation and service of Mini-Split & Central A/C systems utilizing R410a refrigerant. The kit includes a 2 valve R410a aluminum manifold with 60" ball valve hoses, a clutch type flaring tool for tube sizes from 3/16" to 3/4", a 6-in1 SAE torque wrench set for setting R410a flare nuts to proper torque, a set of imperial and metric hex key sets, a 5/16" valve core removal tool which allows for core replacement under pressure, a complete set of straight and 45 degree swivel flare adapters for access to the units high and low side fittings, 5/16" flare caps for convenience and a free tool bag to carry it all in. Read more here...

TLDB CPS Plastic Handle Deburring Tool designed for fast de-burring of edges, tubes and sheets; features swiveling replaceable blades. Deburring tool with high speed steel deburring blade.

Metal Pocket Deburring Tool

6'' duct board knife with rubber handle. Used to fabricate fiberglass duct board. Stainless steel double edge resharpenable blade facilitates easy piercing for inside cuts. The double edge is also ideal for tapping into and trimming flex duct.

6'' duct board knife with wooden handle. Used to fabricate fiberglass duct board. Stainless steel double edge resharpenable blade facilitates easy piercing for inside cuts. The double edge is also ideal for tapping into and trimming flex duct.

Universal metal fin comb. Repair bent condenser fins with this fin straightening tool.

Large universal metal fin comb. Repair bent condenser fins with this fin straightening tool.

Universal six-sided fin straightening tool. Repair bent condenser fins with the TLFC6 Universal 6 sided fin comb straightening tool.

Use the TLMAG1 to magnetize tools in order to keep small screws and nuts in position, especially helpful when working in confined spaces, or demagnetize tools when working on or near electronic circuit boards. Simply insert a screwdriver or nut driver into the (+) opening, slowly draw it out and it's magnetized. Leave the magnetizer on the tool for extra strength. To demagnetize, slowly draw the tool through the smallest area of the (-) opening. The TLMAG1 is an essential tool for the professional and do-it-yourselfer alike.

TLMIR1 CPS Circular Telescoping Mirror 1.25" Diameter. Stretches between  10'' and 14'' inches in length and adjusts into any position for 360 degree viewing.

TLMIR2 CPS Circular Telescoping Mirror 2.25" Diameter. Stretches between 10'' and 14'' inches in length and adjusts into any position for 360 degree viewing.

Rectangular Telescoping Mirror 89 x 54mm (2-1/8" x 3-1/2"). Length can be adjusted from 11-1/4" to 15-1/4". Adjust into any position for 360 degree viewing

Telescoping oval pocket mirror (51 x 25mm). Adjust in length from 6-1/4" to 19-1/2". Adjust into any position for 360 degree viewing.

The TLMKC18 is designed to manually open solenoid valves by magnetically lifting the stem assembly and plunger. Simply slide the TLMKC18 over the valve's enclosing tube and the industrial grade magnets incorporated inside the rugged ABS plastic housing does the rest. It is an ideal tool for trouble shooting/servicing both direct connected or pilot operated 2-way solenoid, 3-way reclaim or 4-way reversing valves. 0.75"/18mm opening fits all common manufactured valves.

Tube Piercing Pliers. Snaps onto refrigerant line and punctures large hole for immediate and maximum full flow to recovery unit. One adjustable tool fits all sizes from 3/16" to 7/8" O. D. hard tubing. Replaceable hardened steel needle and spare gaskets are available.

Replacement Tip For TLPP Tube Piercing Pliers

CPS reamer and burr remover tool. Handles tubes as small as 1/16'' to as large as 1 3/8''. Robust design with steel blades for the removal of both inner and outer burrs.

TLSD1 CPS Autoloader 6-Bit Screw Driver Features a Patented auto loading bit design makes selecting a bit as easy as a twist. Never lose those bits again. 6 replaceable industrial grade 1/4'' hex bits. Includes standard valve core tool bit. Magnetic head holds fasteners in place. Ergonomic high impact housing design. Standard 1/4'' hex drive.

Allen Key Inch Ball Point Key Set: 3/32", 7/64", 1/8", 9/64", 5/32", 3/16", 7/32" and 1/4" (Nickel Plated Finish)

Nickel plated finish hex wrench set for 5/64" through 1/4". Hex keys for 3/32'', 7/64'', 1/8'', 9/64'', 5/32'', 3/16'', 7/32'', and 1/4''.

Hex Wrench Combo includes an inch hex key set and an inch ball point key set with nickle-platted finish.

Metric hex key wrench set for 1.5mm through 8mm with nickel plated finish. Keys for 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, and 8mm.

CPS PRO-SET 124 Service Wrench: 3/16", 1/4", 9/16", 1/2"

127 Offset Service Wrench: 3/16", 1/4", 3/8", 5/16"

Offset Service Wrench: 3/16", 1/4", 3/8", 5/16" (Bulk)

127 Service Wrench: 3/16", 1/4", 3/8", 5/16"

The CPS TLSWT Folding Torx Wrench Set. 8 Sizes; T08, T10, T15, T20, T25, T27, T30, T40. Nickel Plated Steel Alloy Keys. Strong Anodized Handle.

CPS PRO-SET SAE torque wrench set for R-410A installations. Professional interchangeable jaw torque wrench set ensure compliance with OEM torque settings for high pressure R-410A systems. Corresponding settings are clearly marked on torque wrench in Inches. Provides consistently accurate readings and rugged, trouble free performance. Includes six interchangeable jaw sizes (5/8”, 11/16”, 13/16”, 15/16”, 1-1/16”, and 1-5/16”). Includes storage case for long-term protection and is covered by a 1 year product warranty from CPS.

CPS PRO-SET metric torque wrench set for R-410A installations. Professional interchangeable jaw torque wrench set ensure compliance with OEM torque settings for high pressure R-410A systems. Corresponding settings are clearly marked on torque wrench in Netwon Meters (10-75Nm). Provides consistently accurate readings and rugged, trouble free performance.

A step above the standard pocket thermometer the TM50 is packed full of features, including a user selectable temperature alarm, a countdown timer, Min/Max, °F/°C selectable and memory functions. The unit incorporates a highly accurate stainless steel 96mm puncture probe with a 4ft/122cm cord. Temperature range is -58° to 500°F

Digital pocket thermometer with stainless steel probe and pocket clip. Temperature Range: -58° to 302°F / -50° to 150°C User selectable

The CPS TMINI12 infrared thermometer provides instant temperature measurement over a wide range of applications. The unit offers simple one-handed operation, laser point sighting, a backlit display, °C/°F select ability and an automatic power off feature. Use the TMINI12 to quickly measure temperatures of registers, ductwork, furnaces, evaporators, condensers, compressors, relays, manifolds, radiators, exhaust systems, thermostats, bearings and more. 12:1 Ratio -76°F to 932 °F With "K" type input for optional probes.

The CPS TMXKBEAD is a standard K-type bead probe ideally suited for getting fast results when measuring temperature in a variety of media. This 36" long (1 meter) probe provides accurate readings in less than 5 seconds over the range of -58ºF to 400 ºF (-50 ºC to 204 ºC) and is compatible with any other instrument with a
K-Type input.

The CPS TMXSK90 is the fastest and most accurate handheld K-type surface probe providing accurate readings in less than 5 seconds. The sensor is made from flat-spring ribbons of thermocouple material for contact on uneven surfaces. The exposed junction provides for fast response and is compatible with any other instrument with a K-Type input.