View CartMy Account / Order StatusHelp

Join our mailing list!



(Your shopping cart is empty)
You are here: Home > Plasma Cutter Parts > 118-016 5Z031B Dayton 50 amp plasma cutter

118-016 5Z031B Dayton 50 amp plasma cutter



ITEM PART NUMBER DESCRIPTION
1 413-030-666 WHEEL WITH HUB
1 068-024-666 HUBS ONLY
2 413-048-666 AXLE
3 412-329-016 WHEEL MOUNTING BRACKETS (2)
4 410-617-016 BASE
5 412-328-016 FOOT
6 252-004-666 PRESSURE SWITCH
7 246-206-666 GAS SOLENOID
8 410-621-110 FRONT PANEL
9 312-117-666 NOSE
10 238-456-000 COMPLETE TORCH ASSEMBLY
11 4405 O-RING, PK.2
12 4451 NOZZLE, HIGH CURRENT, PK. 3
12 4454 NOZZLE, LOW CURRENT, PK. 3
13 4416 TORCH STAND OFF
14 4453A NOZZLE CAP
15 4450 ELECTRODE, PK, 3
16 4452 SWIRL RING
17 238-228-666 GROUND CABLE WITH CLAMP
17 239-010-102 CLAMP ONLY
18 254-004-666 REGULATOR
19 251-003-666 PRESSURE GAUGE
20 246-225-666 POWER SWITCH
21 246-222-666 AMPERAGE SELECTOR SWITCH, KIT
22 246-224-666 KNOB
23 246-226-666 RUN SETUP SWITCH
24 880-102-666 PRINTED CIRCUIT BOARD
25 880-181-666 10-PIN WIRE HARNESS
26 880-139-666 9-PIN WIRE HARNESS
27 246-199-666 PILOT ARC RELAY
28 880-141-388 TRANSFORMER
29 880-106-888 CONTROL TRANSFORMER
30 244-080-666 RECTIFIER
31 254-005-666 PRE-REGULATOR
32 216-053-666 THERMAL BREAKER
33 245-105-666 RESISTOR, 2fl , 420 W
34 216-086-666 FAN MOTOR
35 316-007-666 FAN BLADE
36 410-629-016 BACK PANEL
37 248-178-666 POWER CORD
38 246-165-666 CONTACTOR
39 830-134-666 RESISTOR ASSEMBLY, 1.5T1 , 160 W
40 880-137-888 REACTOR
41 412-332-110 HANDLE (NOT SHOWN)
42 410-630-076 COVER W/ACCESS PANEL (NOT SHOWN)
43 410-530-016 ACCESS PANEL (NOT SHOWN)

Sort By:
Page of 1
001-288-908 Plasma Torch Hand Grip (Trigger On Bottom)
001-288-908 Plasma Torch Hand Grip (Trigger On Bottom)
Price $45.38

001-288-908 Plasma Torch Hand Grip (Trigger On Bottom). Used on 50-55 Amp Models 118-014 (YA5550), 118-015 (2050), 118-016 (82050,5Z031A, 5Z031B) more info
002-244-908 Plasma Torch Safety Trigger. Used on 50-55 Amp Models 118-014 (YA5550), 118-015 (2050), 118-016 (82050,5Z031A, 5Z031B)
002-244-908 Plasma Torch Safety Trigger
Price $24.82

002-244-908 Plasma Torch Safety Trigger. Used on 50-55 Amp Models 118-014 (YA5550), 118-015 (2050), 118-016 (82050,5Z031A, 5Z031B) more info
098-142-000 Synthetic Lubricant 1/4oz 4424
098-142-000 Synthetic Lubricant 1/4oz 4424
Price $19.18

Synthetic Lubricant for plasma torch O-rings more info
131-280-908 Century Torch Standoff Repl. 4416 / 44160
131-280-908 Century Torch Standoff Repl. 4416 / 44160
Price $53.85

Century / Solar Plasma Torch Stand-Off Kit keeps nozzle clear of dirt, paint and corrosion. Also simplifies cutting with straightedge or pattern. 131-280-908 TORCH STANDOFF Replaces 4416 / 44160. more info
216-082-000 Fan Motor With Leads 240 Volt
216-082-000 Fan Motor With Leads 240 Volt
Price $42.95

216-082-000 Fan Motor With Leads 240 Volt .20 amps C.W. shaft end. Replaces some older models. 216-086-000, 216-086-010, 216-034-000, 216-034-100, 216-034-200, 216-034-666. See 316-007-300 for Fan blade. more info
216-086-666 Fan Motor W/ Leads 240 Volt
216-086-666 Fan Motor W/ Leads 240 Volt
Discontinued See 216-082-000

216-086-666 Fan Motor W/ Leads 240 Volt .55 amp C.W. shaft end rotation. Replaces 216-034-000, 216-034-100, 216-034-200, 216-034-666. See 216-082-000 as a possible replacement. more info
238-285-100 Plasma Torch Assembly
238-285-100 Plasma Torch Assembly
Discontinued See 238-456-000

238-285-100 Plasma Torch Assembly more info
238-285-999 Plasma Torch Head (Old Style Trigger On Top)
238-285-999 Plasma Torch Head (Old Style Trigger On Top)
Discontinued See 238-456-000

238-285-999 Plasma Torch Head (Old Style Trigger On Top) See 238-456-000 for new style with trigger on the bottom. more info
238-456-000 Plasma Torch 50 Amp 25 Foot With Safety Switch
238-456-000 Plasma Torch 50 Amp 25 Foot With Safety Switch
Discontinued

Plasma Torch 50 Amp 25 Foot With Safety Switch. OEM Torch Head hose assembly includes hose, torch head, o-ring, swirl ring, electrode, high current nozzle, nozzle cap. Replaces 238-285-000, 238-285-100. more info
238-456-999 Plasma Torch Head (New Style Trigger On Bottom)
238-456-999 Plasma Torch Head (New Style Trigger On Bottom)
Discontinued See 238-456-000

238-456-999 TORCH HEAD FOR 238-456-000, 50 Amp ,Replaces 238-285-000, 238-285-100. Used on 50-55 Amp Models 118-014 (YA5550), 118-015 (2050), 118-016 (82050,5Z031A, 5Z031B). more info
244-076-666 Century Rectifier Plasma Cutter
244-076-666 Century Rectifier Plasma Cutter
Discontinued See 244-080-666

244-076-666 Century Rectifier Plasma Cutter more info
244-080-666 Century Rectifier Plasma
244-080-666 Century Rectifier Plasma
Price $204.95

244-080-666 244-076-666 Century Rectifier Plasma more info
245-105-666 Century 2 Ohm 420 Watt Resistor
245-105-666 Century 2 Ohm 420 Watt Resistor
Price $167.79

245-105-666 Century 2 Ohm 420 Watt Resistor comes with mounting brackets, insulators and mounting harware. more info
246-086-666 Century Solenoid 24 Volt Air Service, replaces 246-212-666 and 43700008.
246-086-666 Century Solenoid 24 Volt Air Service
Price $115.85

246-086-666 Century Solenoid 24 Volt Air Service, replaces 246-212-666 and 43700008. more info
246-199-666 Pilot Arc Relay 24 Volt DC Coil
246-199-666 Pilot Arc Relay 24 Volt DC Coil
Price $69.95

246-199-666 Pilot Arc Relay 24 Volt DC Coil more info
252-004-666 Century Switch, Air Pressure Service
252-004-666 Century Switch, Air Pressure Service
Price $84.03

252-004-666 Century Switch, Air Pressure Service more info
254-004-666 Century Heavy Duty Regulator
254-004-666 Century Heavy Duty Regulator
Price $106.01

254-004-666 Century Heavy Duty Regulator more info
254-005-666 Century Pre-Regulator (set at 105PSI)
254-005-666 Century Pre-Regulator (set at 105PSI)
Price $110.18

254-005-666 Century Pre-Regulator (set at 105PSI) more info
312-114-000 Handle Both Sides
312-114-000 Handle Both Sides
Discontinued

Plasma Torch Handle Assembly, no hardware included. Molded handles only more info
316-007-300 Fan Blade 7.12" CCW
316-007-300 Fan Blade 7.12" CCW
Price $13.79

316-007-300 Fan Blade 7.12" CCW more info
316-007-666 Fan Blade 7.12" CCW
316-007-666 Fan Blade 7.12" CCW
Discontinued See 316-007-300

316-007-666 Fan Blade 7.12" CCW more info
334-274-100 Trigger Assembly Replaces 334-281-100
334-274-100 Trigger Assembly Replaces 334-281-100
Price $34.10

334-274-100 Trigger Assembly Replaces 334-281-100 more info
334-287-908 Electrode Plasma 50 Amp 3 Pack Repl. 4450 44500
334-287-908 Electrode Plasma 50 Amp 3 Pack Repl. 4450 44500
Price $24.85 3 Pack

Century / Solar Style Electrode. Plasma Cutting Electrodes initiate the high intensity cutting arc and provide the contact necessary for arc maintenance. Electrodes are subject to wear, causing arc to weaken or be intermittent. more info
334-287-908L Electrode Plasma Extended 50 Amp 3 Pack
334-287-908L Electrode Plasma Extended 50 Amp 3 Pack
Price $26.85 3 Pack

Century / Solar Style Electrode. Plasma Cutting Electrodes initiate the high intensity cutting arc and provide the contact necessary for arc maintenance. Electrodes are subject to wear, causing arc to weaken or be intermittent. more info
334-288-908 Swirl Ring Plasma 50 Amp Repl. 4452 44520
334-288-908 Swirl Ring Plasma 50 Amp Repl. 4452 44520
Price $26.50 Each

Century / Solar Style Plasma 50 Amp Swirl Ring. Swirl Ring imparts a swirling current to stabilize the arc. Keep your plasma cutter working at peak performance with these replacement parts.
For plasma torch 238-285-100 or 238-456-000. The 334-288-908 replaces 4452, 44520, 334-288-000, 334-288-100, 334-288-500. Used on Century made model numbers: 118-014 (YA5550), 118-015 (Solar 2050, 2050C), 118-016 (82050, 5Z031A, 5Z031B)
more info
334-289-908 Nozzle Plasma High Current 50 Amp 5pk 4451 44510
334-289-908 Nozzle Plasma High Current 50 Amp 5pk 4451 44510
Price $26.95 5 Pack

Century - Solar Style 50 Amp High Current Plasma Cutting Nozzles (used on 45 50 & 55 amp settings). The Plasma Cutting Nozzle controls arc for smooth cutting. When Purchasing a pair of Nozzles and nozzle caps, they must be the same style and amp rating (i.e. tapered, 15/20 amp). more info
334-289-908L Nozzle Plasma High Current Extended 50amp 5pk
334-289-908L Nozzle Plasma High Current Extended 50amp 5pk
Price $32.95 5 Pack

High Current Extended Plasma Nozzles 50amp 5pk. The Plasma Cutting Nozzle controls arc for smooth cutting. When Purchasing a pair of Nozzles and nozzle caps, they must be the same style and amp rating (i.e. tapered, 15/20 amp). more info
334-290-908 Nozzle Cap Plasma 50amp Extended Type Repl.  4453 44530
334-290-908 Nozzle Cap Plasma 50amp Extended Type Repl. 4453 44530
Price $15.85 Each

Century / Solar Style Nozzle Cap, Extended Type. Nozzle Caps direct cooling air flow to the nozzle and workpiece. more info
334-295-908 Nozzle Plasma Low Current 35-40 Amp 3pk 4454 44540
334-295-908 Nozzle Plasma Low Current 35-40 Amp 3pk 4454 44540
Price $24.95 3 Pack

Century - Solar Style 35 - 40 Amp Low Current Plasma Cutting Nozzles. The Plasma Cutting Nozzle controls arc for smooth cutting. When Purchasing a pair of Nozzles and nozzle caps, they must be the same style and amp rating (i.e. tapered, 15/20 amp). more info
512-087-908 O-Rings 20/40 15 20 50 Amp 2 pack Repl. 4405 44050
512-087-908 O-Rings 20/40 15 20 50 Amp 2 pack Repl. 4405 44050
Price $3.32 2 Pack

Century / Solar Package of 2 O-Rings for 20/40, 15, 20 and 50 amp plasma cutters. The rubber O-Ring prevents air leaks which cause erratic cutting and cooling.

more info
880-102-666 Century Printed Circuit Board
880-102-666 Century Printed Circuit Board
Price $299.55

Century Plasma Cutter Printed Circuit Board. Controls The Pilot Arc Relay, 24 Vdc Solenoid, Trigger, Pressure Switch, 24 Vac main contactor coil, 24 Vdc pilot relay coil. more info
880-134-666 Century 1.5ohm, 160 Watt Resistor
880-134-666 Century 1.5ohm, 160 Watt Resistor
Price $73.77

880-134-666 Century 1.5ohm, 160 Watt Resistor more info
   
 
118-016 5Z031B Dayton 50 amp plasma cutter
Century Tool & Equipment
4013 S. Old Hwy 94
St. Peters MO 63304
 About Us
 Let Us Repair It
 Privacy Policy
 Send Us Feedback