| IR 2908P 3/4" Drive Parts List | |||
| Item | PartNumber | PartDescription | IREquivalent |
| 1 | Motor HousingAssembly | 2908-A40 | |
| * | Trigger Assembly | 7AH-A93 | |
| 3 | Trigger | 5RA-93 | |
| 4 | Trigger Pin | 7AH-94 | |
| 5 | ExhaustSilencer | 2908-311 | |
| 6 | Exhaust Deflector | 2908-23 | |
| 7 | Throttle ValveSeat | 2908-303 | |
| 8 | Throttle Valve | 2908-302A | |
| 9 | Throttle ValveSpring | 2908-51 | |
| 10 | Oiler BodyAssembly | 2908-A198 | |
| 11 | Oiler BodySeal (2) | AF120-290 | |
| 12 | Oiler Plug | 77H-75 | |
| 12A | OilerRetaining Ring | 2908-304 | |
| 13 | Air StrainerAssembly | 804-465 | |
| 14 | Oil Chamber Plug Seal | R3-92A | |
| 15 | Oil ChamberPlug | D92-227 | |
| 16 | Reverse ValveBushing Assembly | 2908-A330 | |
| 17 | Reverse ValveBushing Seal (2) | AF120-290 | |
| 18 | Reverse Valve | 2908-329 | |
| 19 | Reverse Valve Detent Ball | AV1-255 | |
| 20 | Reverse ValveDetent Spring | 231-664 | |
| 21 | Reverse ValveKnob | 231-666 | |
| 22 | Reverse ValveKnob Screw | 231-665 | |
| 23 | Grease Fitting | 130SR-188 | |
| 24 | End PlateGasket | 2908-283 | |
| 25 | Rear Rotor Bearing Retainer | R4800-119 | |
| 26 | Rear RotorBearing | R1A-510 | |
| 27 | Rear End Plate | 2908-12 | |
| 28 | Rotor | 2908-53 | |
| 29 | 2173 | Rotor Vane(requires 6) | 2908-42-6 |
| 30 | Cylinder | 908-3 | |
| 31 | Cylinder Dowel | 403-98A | |
| 32 | Front EndPlate Dowel | 230-74 | |
| 33 | Front End Plate | 2908-11 | |
| 34 | Front Rotor Bearing | R38P-606 | |
| 35 | Motor ClampWasher (2) | 2908-207 | |
| 36 | Hammer FrameAssembly | 2908-A703 | |
| 37 | Hammer Pin (2) | 2908-704 | |
| 38 | Rear HammerFrame Washer | 2908-706 | |
| 39 | Hammer (2) | 2908-724 | |
| 40 | Hammer Case Assembly (for 2908P1& 2908P2) | 2908-A727 | |
| 40 | Hammer Case Assembly (for2908P1-EU & 2908P2-EU) | 2908-EU-727 | |
| * | Hammer CaseLabel (for 2908P1 & 2908P2) | WARNING-2-99 | |
| * | Hammer CaseLabel (for 2908P1-EU & 2908P2-EU) | EU-99 | |
| 42 | Hammer CaseBushing | 2908-641 | |
| 43 | Hammer CaseGasket | 1709-36 | |
| 44 | Hammer CasePilot | 2908-800 | |
| 45 | Hammer CaseLock Washer (4) | 8U-58 | |
| 46 | Hammer CaseCap Screw (4) | R0H-354 | |
| 46 | Anvil Assembly (5/8" squaredrive) | 2908-P726 | |
| 46 | Anvil Assembly (3/4" squaredrive) | 2908-P826 | |
| 47 | SocketRetaining Ring (5/8" square drive) | 808-716 | |
| 47 | Socket Retaining Ring (3/4"square drive) | 2908-716 | |
| 48 | Socket Retaining Pin Spring | 5UHD-718 | |
| * | Quick-Change Anvil Assembly(5/8" hex recess) | 2908-A926-10 | |
| 49 | Quick Change Anvil | 2908-926-10 | |
| 50 | Thrust Ring Lock (2) | 908-933-10 | |
| 51 | Retaining Ball (7/32" diameter) | 2U-722 | |
| 52 | Retaining Sleeve | 908-930-10 | |
| 53 | Retaining Sleeve Spring | 908-931-10 | |
| 54 | Thrust Ring | 908-932-10 | |
| * | Nameplate (for 2908P1 &2908P2) | 2908-301 | |
| * | Nameplate (for 2908P1-EU &2908P2-EU) | 2908-EU-301 | |
| * | Vertical Hanger | 2908-365 | |
| * | Grease Gun | R000A2-228 | |
| * | Tune-up Kit (includes 5, 7, 9, 14, 17 [2], 19, 20, 24, 25, 26, 27, 29, 34 & 42) | 2908P-TK2 | |
