View CartMy Account / Order StatusHelp

Join our mailing list!



(Your shopping cart is empty)

  Home > Battery Charging Equipment > Wheeled Battery Chargers - Automatic Operation >

IBC6008 Associated 60 Amp 12 Volt Automatic Automotive Battery Charger / Analyzer Engine Start

IBC6008 Associated 60 Amp 12 Volt Automatic Automotive Battery Charger / Analyzer
 
Price $799.95


Product Code: ASOIBC6008
Qty:

Description Prop65
 
IBC6008 Associated 60 Amp 12 Volt Automatic Automotive Battery Charger / Analyzer provides safe effective charging at 12 Volt for Flooded / Maintenance Free, AGM, Gel Cell, and Deep-Cycle Batteries, as well as Spiral Cell, Orbital or Optima Batteries. The Electrical Stability System (ESS™) technology turns IBC6008 into a stable power supply for extended service procedures or re-flashes while the battery is removed while maintaining a nominal 13.7V DC Output. The Deep Discharge and Recovery with desulfation mode enables the user to recover dead batteries ultimately saving the cost of the unit over several batteries that would have normally gone to waste. The Dead battery over ride switch brings batteries above the 4 volt minimum for testing and charging eliminating the need to pre-charge before testing. The 270 Amp boost for helps jump start vehicles. Made in the U.S.A. The "Does Everything" wheel charger which has 60 Amp charge rate and 270 Amps of crank assist.

Charging Modes:
  • REFLASH POWER – Used to hold the voltage on the battery at the set value while the vehicle is being serviced. Do not use without battery.
  • MEMORY SAVER – Is used with the Memory Saver option to hold up the vehicle voltage while charging the battery. Plug cable into the power plug, then set charger for MS and press ON/OF to start. If it does not see a voltage on the MS it will show an Error.
  • CRANK – Used to assist starting a vehicle. Select and follow the screen prompts.
  • MANUAL – This mode can be used to operate the charger just like a manual charger runs for the time set while limiting the current and voltage.
Battery Type:
  • Standard Automotive
  • Deep‐cycle
  • AGM
  • Gel Cell
Maximum Current:
  • Limits current out put of the charger
  • Can be used to limit heating of the battery
  • Some batteries have limits on maximum current for charging
Hold Voltage: Depending on the battery type this could be the maximum voltage the battery is charged at or it may be gassing point where the current is reduced to charge the battery for maximum charge efficiency.
Run Time: This would be the maximum charge time allowed for charging the battery.
Safety Voltage: If this voltage is reached and cannot be reduced the charge is terminated.
Finish Current: Depending on the battery type, this current is the current the charge is terminated on or the current used to finish the charge.
Time Post Gassing: This is the maximum time allowed after reaching the hold voltage.
Finish Types:
  • NONE: – When charge is done just turns off.
  • PULSE/TIME: – After charge is complete, charge remains OFF until the selected time is reached then charger will turn back on terminating again the hold voltage is reached.
  • PULSE/VOLTS: – After the charge is complete the charger will remain OFF until the battery voltage drops to the selected Float voltage then charger will turn on and charge until it reaches the hold voltage.
  • FLOAT: – After the charge complete will allow the battery voltage to fall back until reaches the FLOAT VOLTAGE then it will hold at the FLOAT VOLTAGE until the battery is removed
Product Features
  • Micro-processor controlled and fully automatic
  • Electrical Stability System (ESS) technology turns the IBC6008 into a stable supply for extended service procedures or re-flashes. Nominal 13.7V DC output
  • Program for deep discharge recovery of flooded batteries
  • Patented diagnostics indicate weak or defective battery
  • Charges all types of 12 volt batteries
  • Designed for AGM, Gel Cell, Sealed, and Standard Flooded batteries including Spiral cell, Orbital, or Optima batteries
  • Reverse polarity protected
  • "Safe In Any Weather" Operation
  • UL Listed
  • MADE IN USA

Charger Specifications:

Model Number: IBC6008
DC Output: 60 Amps / 70 Amps in Power Supply Mode, 15Amp Continuous
DC Leads: 6 ˝’ 4 AWG
Clamp Rating: 400A
Boost Rating: 270A
AC Cord / Voltage: 6’ 16‐3 / 120VAC 60 Hz
Battery Types: 12 Volt Flooded, AGM, and Gel Cell batteries ‐ including Spiral Cell, Orbital™, or Optima™ batteries
Display: Analog Meter and 3 LED display indicating charge status
Limited Warranty: 5 Years
Shipping Dimensions: 17”x16”30”
Weight: 49 LBS


Browse for more products in the same category as this item:

Battery Charging Equipment > Wheeled Battery Chargers - Automatic Operation
Associated Battery Chargers
Battery Charger Parts > Associated Battery Charger Parts Listing By Model > 6003 NEWSTYLE Associated Battery Charger Parts List
Battery Charging Equipment > Marine, Deep Cycle, AGM, GEL Battery Chargers
Battery Charger Parts > Associated Battery Charger Parts Listing By Model > ESS6008 Associated Battery Charger Parts List
Battery Charger Parts > Associated Battery Charger Parts Listing By Model > ESS6008 Associated Battery Charger Parts List (New Style)
Battery Charger Parts > Associated Battery Charger Parts Listing By Model > IBC6008 Associated Battery Charger Parts List
Century Tool & Equipment
4013 S. Old Hwy 94
St. Peters MO 63304
 About Us
 Let Us Repair It
 Privacy Policy
 Send Us Feedback