Automotive tools & equipment

HVAC & Industrial supplies

Sales - parts -service

You are here: Home > Battery Charger Parts > Schumacher Battery Charger Repair Parts > SE-2151MA Schumacher Battery Charger Parts List

SE-2151MA Schumacher Battery Charger Parts List

There are several versions of this unit, please pay close attention to parts specifications to ensure proper placement as there are no returns on components. If you do not see the correct part for your unit always call first before ordering.
For SCR Units Use:
  • 2299001227 Heatsink / Circuit Board Combo
  • 2299001165 Circuit Board

For 4 Diode Units Use:

  • 2299000949 Diode SCR Heatsink
  • 2299000906 Circuit Board
Part No.
Description
Qty
0090026068
115 Volt Power Cord
1
0499000032
2 Position Slide Selector Switch SPDT (3 Pins)
1
0499000070
4 Position Slide Selector Switch
1
2299000906
PC Charging Board
1
2299000949
Heatsink Rectifier SCR Assembly 1
2299001165
PC Charging Board
1
2299001227
Heatsink Rectifier and Control Board Assembly
1
3599000240
Battery Charger Handle
1
3899001205
Output Clamps and Cables Set Red & Black 10 Gauge
1
3899002538
Output Clamps and Cables Set Red & Black 10 Gauge 82"
1
3999000056
12 Volt 35 Amp Circuit Breaker
1
5399100120
Ammeter Horizontal (For SCR Units with Lights) 0-100 Amp 1
5399100137
Ammeter Horizontal 0-80 Amp
1
Sort By:
Page of 1
0090026068 Schumacher 115 Volt Power Cord 0090026068 Schumacher 115 Volt Power Cord

Power Cord 115 Volt 3 Prong. Termination Specs, 1/8" Shielded Female Quick Connect (White), Ring Terminal (Ground), Split Terminal (Black).

Discontinued
0499000032 Schumacher 2 Position Slide Selector Switch SPDT (3 Pins) 0499000032 Schumacher 2 Position Slide Selector Switch SPDT (3 Pins)

2 Position Slide Selector Switch Single Pole Double Throw Contacts 6amp 125VAC Rating (3 Pins)

Price $12.45
2299000906 Schumacher PC Charging Board (3 Wire) 2299000906 Schumacher PC Charging Board (3 Wire)

PC Charging Board includes wiring. Requires soldering to install on SCR Heatsink. 3 Wires, Black, Green, Grey. Single green LED. (Positive out at the QC terminal)

Discontinued
2299000915 Schumacher PC Charging Board (3 Wire) 2299000915 Schumacher PC Charging Board (3 Wire)

PC Charging Board includes wiring. Requires soldering to install on SCR Heatsink. 3 Wires, Black, Green, Grey. Single green LED.

Discontinued
2299000949 Schumacher Heatsink Rectifier (4 Diode Units) 2299000949 Schumacher Heatsink Rectifier (4 Diode Units)

Heat Sink Rectifier Assembly, 4 Diode 75 Amp Rating with SCR mounted. Some soldering required for installation on circuit board. Requires soldering to install on PC Board.

Discontinued
2299001165 Schumacher PC Charging Board (7 Wire) 2299001165 Schumacher PC Charging Board (7 Wire)

PC Charging Board includes wiring. Controls charging on several models. Requires soldering to install on SCR Heatsink. This board has 2 LED's Red, Green.

Discontinued
2299001227 Schumacher Heatsink Rectifier And Circuit Board Assembly (7 Wire) 2299001227 Schumacher Heatsink Rectifier And Circuit Board Assembly (7 Wire)

Heatsink Rectifier Circuit Board Assembly completely assembled. No soldering required. Unit comes complete with aluminum heat sink, and circuit board ready to install. Automatic charging board with 4 transformer leads and 3 switch leads 1 red and 1 green led.

Discontinued
2700000020 Schumacher Power Cord Strain Relief For DC Leads 2700000020 Schumacher Power Cord Strain Relief For DC Leads

Power Cord Strain Relief Protects the lifeline of your electric/electronic products by absorbing the forces of pull, push, and twist that may be exerted on the flexible power cord. Securely anchors, insulates, and protects cables at panel entry points.

Price $1.19
3599000240 Schumacher Battery Charger Handle 3599000240 Schumacher Battery Charger Handle

3599000240 Schumacher Battery Charger Handle. Works with many other brand chargers. 9.75" Total Length.

Discontinued
3899001205 Schumacher Clamps Cables Red & Black Set 10 Gauge 84" 3899001205 Schumacher Battery Clamps Cables Red & Black Set 10 Gauge 84"

Battery Charger Clamps Cables Red & Black Set. 7ft Long, 10ga, 1/4" quick disconnect on negative lead, ring terminal on positive lead. Used on chargers with 100 amp max rates. Can be used as a generic replacement for large size bench top chargers.

Discontinued
3899002538 Schumacher Clamps Cables Red & Black Set 10 Gauge 82" 3899002538 Schumacher Battery Clamps Cables Red & Black Set 10 Gauge 82"

New Style DC Output Clamp And Cable Set Red Positive, Black Negative. 82" Long, 10ga, Ring Terminal connectors. Steel Clamp. Used on chargers with 125 amp max rates.

Price $15.45
3999000056 Schumacher 12 Volt 35 Amp Circuit Breaker 3999000056 Schumacher 12 Volt 35 Amp Circuit Breaker

12 Volt 35 Amp Circuit Breaker

Discontinued
5399100120 Schumacher Ammeter Horizontal 0-100 Amp 5399100120 Schumacher Ammeter Horizontal 0-100 Amp

Ammeter Horizontal 0-100 Amp features easy snap-in installation, no tools required. Orange Red Charge Rate face with Full Charge & Check Battery Indicator Light Portals. 0-15 Amp  charging range and 15-100 Amp starting range. 1/4" Spade Terminal Connections for ease of installation.

Discontinued
   
 
There are several versions of this unit, please pay close attention to parts specifications to ensure proper placement as there are no returns on components. If you do not see the correct part for your unit always call first before ordering.
*Variations of models due to production changes and parts availability are not our responsibility
*No refunds on electrical components
*Service should be performed only by a qualified technician
*Please read all supporting documentation and safety instructions
For SCR Units Use:
  • 2299001227 Heatsink / Circuit Board Combo
  • 2299001165 Circuit Board

For 4 Diode Units Use:

  • 2299000949 Diode SCR Heatsink
  • 2299000906 Circuit Board
Schumacher SE-40MAP, SE-70MA, SE-82-6, SE-125A, SE-520MA, SE-1010-2, SE-1052, SE-1250, SE-1275A, SE-1510MA, SE-2151MA & SE-5212A Troubleshooting Guide
PROBLEM POSSIBLE CAUSE SOLUTION
No reading on the ammeter. Charger is not plugged in. Plug the charger into an AC outlet.
No power at the receptacle. Check for open fuse or circuit breaker supplying AC outlet.
Clips are not making a good connection to the battery. Check for poor connection to battery and frame. Make sure connection points are clean. Rock clips back and forth for a better connection.
Connections are reversed. Unplug the charger and reverse the clips.
Battery is defective (will not accept a charge). Have battery checked.
2 amp charge rate is being used. Ammeter may show no activity at the 2A charge rate.
Ammeter reading stays high. Battery is severely discharged. Continue charging battery for two more hours. If problem continues have the battery checked.
Wrong battery voltage. Verify the voltage settings on the charger are correct.
Charger will not turn on when properly connected. AC outlet is dead. Check for open fuse or circuit breaker supplying AC outlet.
Poor electrical connection. Check power cord and extension cord for loose fitting plug.
The battery is connected and the charger is on, but is not charging. Clips are not making a good connection. Check for poor connection at battery and frame. Make sure connecting points are clean. Rock clips back and forth for a better connection.
The measured current is much lower than what was selected. The charger reached the maximum voltage and is reducing the current. No problem, this is a normal condition.
Ammeter reads less than selected charge rate when charging a discharged battery Extension cord is too long or wire gauge is too small. Use a shorter or heavier gauge extension cord.
Weak cell or sulfated plate in battery. A sulfated battery will eventually take a normal charge if left connected. If the battery will not take a charge, have it checked.
Battery is only partially discharged. Continue to charge the battery.
The charger is making an audible clicking sound. Circuit breaker is cycling. The settings may be wrong. Check the charger settings.
Battery is defective. Have the battery checked.
Shorted battery cables or clips. Circuit breaker cycles when current draw is too high. Check for shorted cables or clips and replace if necessary.
Severely discharged battery, but otherwise it is a good battery. The battery may not want to accept a charge due to a run-down state. Allow charging to continue until battery has a chance to recover sufficiently to take a charge. If more than 20 minutes, stop charging and have the battery checked.
Reverse connections at battery. Shut the charger off and correct the lead connections.
Charger makes a loud buzz or hum. Transformer laminations vibrate (buzz). No problem, this is a normal condition.
Shorted Diode Assembly or Output Rectifier Assembly (hum). Have charger checked by a qualified technician.
Short or no start cycle when cranking engine. Drawing more than the Engine Start Rate. Crank time varies with the amount of current drawn. If cranking draws more than the Engine Start Rate, crank time may be less than 3 seconds.
Failure to wait 4 minutes (240 seconds) between cranks. Wait 4 minutes of rest time before the next crank to allow the battery and charger to cool down.
Clips are not making a good connection. Check for poor connection at battery and frame.
AC cord and/or extension cord is loose. Check power cord and extension cord for loose fitting plug.
No power at receptacle. Check for open fuse or circuit breaker supplying AC outlet.
The charger may be overheated. The thermal protector may have tripped and needs a little longer to close. Make sure the charger vents are not blocked. Wait and try again.
Battery may be severely discharged. On a severely discharged battery, charge for 10 to 15 minutes in the highest manual rate to help assist in cranking.
Schumacher User Manual Link

When a charging problem arises, make certain that the battery is capable of accepting a normal charge. Double check all connections, AC outlet for a full 120-volts, charger clips for correct polarity and the quality of the connections from the cables to the clips and from the clips to the battery system. The clips must be clean.

When a battery is very cold, partially charged or sulfated, it will not draw the full rated amperes from the charger. It is both dangerous and damaging to a battery to force higher amperage into it than it can effectively use in recharging.