SE-4022 Schumacher Battery Charger Parts List
SchumacherSE-4022 Repair Parts
|
Part No.
| Description
| Qty
|
0090026125
| 115 Volt Power Cord
| 1
|
0099000045
| Knob for Selector Switches on SESeries Chargers | 1
|
0099000062
| Fan Blade
| 1
|
0099000063
| Fan Motor Open Frame 115 Volt
| 1
|
0099000080
| Wheel 6" Plastic for 3/8"Diameter Axle
| 1
|
0099000094
| 135 Minute Timer Mechanical withHold
| 1
|
0099000096
| Knob for Timer Switches on SESeries Chargers | 1
|
0499000022
| 6 Position Rotary SelectorSwitch (Old Style)
| 1
|
0499000050
| Rocker Switch 2 Position 3Terminal On-On
| 1
|
0499000051
| 6 Position Rotary Selector Switch
| 1
|
1199003352
| Metal Foot
| 1
|
2199700006
| Axle End Cap 0.375" DiameterAxle (Pair)
| 1
|
2299000649
| Heatsink Rectifier Assembly | 1
|
2299001023
| Battery Charger Wheels - HandleHardware Kit
| 1
|
0099001542
| 12 Volt DC Fan Speed Controller(Three Wire)
| 1
|
2299001552
| Heatsink Rectifier Assembly | 1
|
2299001565
| Fan Motor 12 Volt DC MuffinUltra Quiet
| 1
|
2299001587
| Heatsink Rectifier Assembly
| 1
|
2299001651
| Heatsink Rectifier Assembly | 1
|
2299002310
| 12 Volt DC Fan Speed Controller(Two Wire)
| 1
|
3100100032
| Diode Anode on Lead 90 Amp
| 1
|
3199100028A
| 75 Amp 400 Volt Positive Diode(Set of 4)
| 1
|
3599000210
| Battery Charger Handle
| 1
|
3899000391
| Output Cable and Clamp BlackNegative
| 1
|
3899000408
| Output Cable and Clamp RedPositive | 1
|
3899001140
| Output Cable and Clamp BlackNegative 6 AWG 80" | 1
|
3899001141
| Output Cable and Clamp RedPositive 6 AWG 80" | 1
|
3899001968
| Output Cable and Clamp BlackNegative 6 AWG 83" | 1
|
3899001969
| Output Cable and Clamp RedPositive 6 AWG 88"
| 1
|
3999000107
| Circuit Breaker 32 Volt DC 90 Amp
| 1
|
3999000108
| Circuit Breaker 32 Volt DC 100Amp
| 1
|
4999001229
| Fan Motor 12 Volt DC MuffinUltra Quiet
| 1
|
5199000406
| Circuit Breaker Connection Screw
| 1
|
5399100082
| Ammeter Horizontal 0-200 AmpRange
| 1
|
5399100141
| Ammeter Horizontal 0-200 Amp
| 1
|
5399200013
| Voltmeter Testmeter with CircuitBoard
| 1
|
8019K96
| Single Male to Double MaleSplitter Piggyback Spade Terminal (Pair)
| 1
|
When a charging problem arises, make certain that the battery is capable of accepting a normal charge. Double check all connections, AC outlet for a full 120-volts, charger clips for correct polarity and the quality of the connections from the cables to the clips and from the clips to the battery system. The clips must be clean.
When a battery is very cold, partially charged or sulfated, it will not draw the full rated amperes from the charger. It is both dangerous and damaging to a battery to force higher amperage into it than it can effectively use in recharging.
![]()
There are several versions of production on this unit, please view all products before making a selection.
![]()
Older units may have a 5 terminal switch. Use
0499000022 Schumacher Rotary Selector Switch for these units.
![]()
The rectifier for this unit has changed several times, please view all products before making a selection.
![]()
The fan motor for this unit has changed several times, please view all products before making a selection.
![]()
The fan speed controller for this unit has changed several times, please view all products before making a selection.
![]()
The cable/clamp assembly for this unit has changed several times, please view all products before making selection.
![]()
The circuit breaker for this unit has changed several times, please view all products before making selection.
![]()
The ammeter for this unit has changed several times, please view all products before making selection.
| TROUBLESHOOTING |
| If a problem does occur, check the following: |
| PROBLEM | POSSIBLE CAUSE | SOLUTION |
| No Meter Reading (AC Cord Unplugged) | Clips are not making a good connection. | Rock clips back and forth for a better connection. |
| Battery voltage is too low. | Plug AC line into outlet. Meter should now indicate. |
| 2 amp charge rate being used. | None, meter will not indicate here. |
| Charger will not turn on when properly connected. | AC outlet is dead. Poor electrical connection. | Plug in a lamp to check for voltage. Check connections, rock back and forth for a better connection. |
| Clicking noise from charger. | Circuit breaker is cycling. | May be in the wrong switch position |
| Battery is defective. | Have Battery checked. |
| Severely discharged battery but otherwise a good battery. | Allow charging to continue until battery has a chance to recover sufficiently to take a charge. If more than 20 min. stop charging and have the battery checked. |
| Reverse connections at battery. | Shut off charger and correct lead connections. |
*Variations of models due to production changes and parts availability are not our responsibility
*No refunds on electrical components
*Service should be performed only by a qualified technician
*Please read all supporting documentation and safety instructions
There are several versions of production on this unit, please view all products before making a selection.
