 |
 |
 |
|
The PL6850 is designed to provide stable power, on demand up to 120 amps, to a vehicle electrical system to support module reprogramming. It is also designed specifically for fleet service battery charging with a maximum charge rate of 120 amps, to quickly and effectively bring 4- and 8-battery Group 31 packs back to full charge
In power supply mode, the PRO-LOGIX PL6850 provides power to maintain vehicle electrical system voltage at a preset level, increasing its output in response to system load increases to maintain a stable power environment for successful reprogramming. It features a voltage output range of 13.1-14.9V, adjustable in 0.1V increments. allowing the operator to dial the output in exactly as specified by the supplier of the vehicle under service. It features fast load responsiveness for ultra-quick recovery from system demand increases. It also delivers its massive power with minimal voltage ripple (<100mV), providing a clean flow of power to the vehicle without risk of programming interference.
In charging mode, the PL6850 utilizes advanced microprocessor-controlled logic to precisely deliver a fully automatic charging routine designed to optimally charge and maintain each battery or battery pack serviced. The PL6850 features the ability to properly charge a wide variety of lead acid battery types, including Conventional, AGM, Spiral Wound, Start-Stop, Deep Cycle and Marine lead acid batteries, plus LiFEPO4 Lithium Batteries – enabling beneficial service of virtually any battery type installed in a vehicle. The PL6850 adapts its charging approach based on the needs of each battery or battery pack it services. Such adaptations can include activating a soft start mode on deeply discharged batteries, a battery repair mode on older/distressed batteries and temperature compensation when charging in extreme temperatures. It also incorporates numerous features to make charging safer for the operator and the vehicle/battery being charged, including over-voltage protection, reverse polarity protection, smart clamp technology and battery fault detection.
In charging mode, the PL6800 adapts its approach based on the needs of each battery or battery pack it services. Such adaptations can include activating a soft start mode on deeply discharged batteries, a battery repair mode on older/distressed batteries and temperature compensation when charging in extreme temperatures. It also incorporates numerous features to make charging safer for the operator and the vehicle/battery being charged, including over-voltage protection, reverse polarity protection, smart clamp technology and battery fault detection.
Specifications - Operating Voltage : 12/24V
- Operational Mode : Automatic
- 12V Charging Rates : 120/60/40/10A
- 24V Charging Rates : 60/40/10A
- Charging Phases : 7
- Battery Types Charged : Flooded, AGM, Spiral, Deep Cycle, Marine, LiFePO4 Lithium
- 12V Power Supply Output : 0-120A on Demand, 13.1-14.9V
- 24V Power Supply Output : 0-60A on Demand, 26.2-29.8V
- Maximum Voltage Ripple in PS Mode : 100mV
- Reverse Polarity Protection : Yes
- Battery Fault Detection : Yes
- Temperature Compensation : Yes
- Output Cable Length : 13′
- Output cable Gauge : #2AWG
- AC Input : ***Requires 20A service***
- Weight : 27 lbs.
- Warranty : 1 Year Limited
 Warning: This product may expose you to chemicals including lead which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Product Features
The unit includes a carry handle for easy transport around a shop or in and out of a mobile service vehicle.
- 0-120A (12V), on demand, power supply mode to maintain system voltage
- 0-60A (24V), on demand, power supply mode to maintain system voltage
- Power supply mode provides optimal support for vehicle reprogramming and ADAS recalibration
- Power supply mode has minimal voltage ripple (<100mV)
- Power supply mode features Rapid Load Response (RLR) technology
- 120/60/40/10A (12V) charging modes allow quick, efficient charging of all battery sizes
- 60/40/10A (24V) charging modes allow quick, efficient charging of all battery packs
- Properly charges Flooded, AGM, Spiral Wound, Deep Cycle, Marine Lead Acid Batteries
- Properly charges Lithium Iron Phosphate (LiFePO4, LFP) Batteries
- Forced Start Mode allows charging of totally dead (0.0V) batteries
- Soft Start Mode enables safe chargiing of severely depleted batteries
- Battery Repair Mode overcomes battery sulfation to restore reserve capacity
- Reverse polarity protection and battery fault detection
- Extra-long 13′ cable reach
- Output cables are detachable (welding connectors) and field replaceable
- PowerJaw clamps provide improved access to hard-to-reach batteries
- PowerJaw clamps allow the hood to be closed (most vehicles) during ADAS calibration
- Includes handle kit for each transport
- Requires 20A service
|
|
|
|
|
|
|