|
|
|
|
The Schumacher 93130 has all the performance features as the Schumacher 93100 but with added power from 230 volt input. Comes complete with 6 foot ground cable and MIG gun, sample spool of .024 steel welding wire, extra contact tips and nozzles, dual-gauge gas regulator, and welding mask. Four heat settings - Cold wire design â no false arcs - Handles solid MIG (with shielding gas) or flux cored welding wires. Easy polarity change terminals under hood. Quick set drive tensioning system â toggle release to maintain optimum tension when changing wire spools - Twin spindles to hold two different spools simultaneously. Saves time when changing wire types. 8 foot power cord (customer supplied plug). Per the User's Guide: "The 230V version of this welder comes from the factory without an input plug. This is due to the wide variety of receptacles and installation options available."
Designed for auto body repair, maintenance, and sheet metal fabrication. The welder consists of a single-phase power transformer, stabilizer, rectifier, and a unique built-in control/feeder. This MIG welder is capable of welding with .024", .030”, and .035" solid wire on DC Reverse (electrode positive) polarity and with .030" and .035" flux core wire on DC Straight (electrode negative) polarity. Now you can weld 26-gauge sheet metal up to 1/4" with a single pass. Welds thicker metal with beveling and multiple pass. Note: 230 volt model welds up to 5/16” in a single pass.
WELDER PERFORMANCE: Your welder has been designed to weld on steel from approximately 26 gauge up to 1/4" thick. Thinner and thicker material can be welded depending on the experience and technique of the welder and the type of welding wire being used. From the factory, this welder is set up to run .024" solid welding wires (a starter spool of .024” wire is included). Additionally, other materials can be welded such as aluminum, stainless steel, and other alloy materials. As assembled from the factory, the welder will require an external supply of compressed shielding gas (not included).
Warning: This product may expose you to chemicals including lead which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
|
|
|
|
|
|
|
|
|
|
|
|
|
Product Features
- Schumacher Pro Series 130amp MIG wire feed welder
- 220v 170 Amps DC max output
Includes:
- Ground cable with clamp
- Mig Gun
- (3) Nozzles
- (3) .023 - (3) .030 Tips
- Gas Hose with clamps
- Regulator
- Welding Face Shield with shade
Specifications
- 10 wire speed settings
- 4 Heat settings
- 220v (No Plug)
- 170 ADC max output
- 90 Day Warranty
SPECIFICATIONS |
|
120
VOLT MODELS |
230
VOLT MODELS |
Input Voltage |
120
volt 60 Hz. Single Phase |
230
volt 60 Hz. Single Phase |
Input Amps @ Rated Output |
20
AAC |
15
AAC |
Input Plug Style |
120
volt 15 amp |
Plug
not included |
Power Cord Length |
8-ft. |
8-ft. |
Rated Output Amps |
65
ADC |
115
ADC |
Max Output Amps |
130
ADC |
170
ADC |
Rated Output Volts |
20
VDC |
19
VDC |
Rated Duty Cycle |
0.2 |
0.15 |
Max Open Circuit Voltage |
30
VDC |
31
VDC |
Agency Listing |
cCSAus |
cCSAus |
Output Settings |
4 |
4 |
Wire Feed System |
Two-roll system with quick reset, indexed
tension, side load |
Two-roll system with quick reset, indexed
tension, side load |
Wire Spool Capacity |
4 to 8-in. diameter - up to 11 lbs. |
4 to 8-in. diameter - up to 11 lbs. |
|
|
|
|
|
|
|