Automotive tools & equipment

HVAC & Industrial supplies

Sales - parts -service

You are here: Home > Battery Charger Parts > Schumacher Battery Charger Repair Parts > SE-3000 Schumacher Battery Charger Parts List

SE-3000 Schumacher Battery Charger Parts List



Schumacher SE-3000 Repair Parts
Part No.
Description
Qty
0090026133
115 Volt Power Cord
1
0099000045
Knob for Selector Switches on SE Series Chargers 1
0099000062
Fan Blade
1
0099000063
Fan Motor Open Frame 115 Volt
1
0099000066
Battery Charger Axle 3/8" Diameter
1
0099000080
Wheel 6" Plastic for 3/8" Axle
1
0099000094
135 Minute Timer Mechanical with Hold
1
0099000096
Knob for Timer Switches on SE Series Chargers
1
0099000123
Foot for 6" Wheeled Units
1
0499000025
7 Position Rotary Selector Switch
1
1199003352
Metal Foot
1
2199700006
Axle End Cap 0.375" Diameter Axle (Pair)
1
2299001067
Battery Charger Wheels - Handle Hardware Kit
1
2299001173
Heatsink Rectifier Assembly 1
2299001587
Heatsink Rectifier Assembly 1
2299001651
Heatsink Rectifier Assembly
1
2299002058
12 Volt Fan Motor Assembly
1
2299002070
12 Volt DC Dural Fan Motor Control
1
3199100028A
75 Amp 400 Volt Positive Diode (Set of 4)
1
3599000662
Battery Charger Handle
1
3899001140
Output Cable and Clamp Black Negative 6 AWG 80" 1
3899001141
Output Cable and Clamp Red Positive 6 AWG 80" 1
3899001968
Output Cable and Clamp Black Negative 6 AWG 83" 1
3899001969
Output Cable and Clamp Red Positive 6 AWG 88"
1
3999000109
Circuit Breaker 32 Volt DC 105 Amp
1
5399100084
Ammeter Horizontal 0-80 Amp 1
5399100143
Ammeter Horizontal 0-80 Amp
1
8019K96
Single Male to Double Male Splitter Piggyback Spade Terminal (Pair)
1


Schumacher SE-2254, SE-2352, SE-3000, SE-3612, SE-4020, SE-4022, SE-5025, SE-6030 & SE-8050 Troubleshooting Guide
PROBLEM POSSIBLE CAUSE SOLUTION
No reading on the ammeter. Charger is not plugged in. Plug the charger into an A.C. outlet.
No power at the receptacle. Check for open fuse or circuit breaker supplying A.C. outlet.
Clips are not making a good connection to the battery. Check for poor connection to battery and frame. Make sure connection points are clean. Rock clips back and forth for a better connection.
Connections are reversed. Unplug the charger and reverse the clips.
Battery is defective (will not accept a charge). Have battery checked.
2 amp charge rate is being used. Ammeter may show no activity at the 2A charge rate.
Ammeter reading stays high. Battery is severely discharged. Continue charging battery for two more hours. If problem continues have the battery checked.
Wrong battery voltage. Verify the voltage settings or output ratings on the charger are correct.
Ammeter reads less than selected charge rate when charging a discharged battery. Extension cord is too long or wire gauge is too small. Use a shorter or heavier gauge extension cord.
Weak cell or sulfated plate in battery. A sulfated battery will eventually take a normal charge if left connected. If the battery will not take a charge, have it checked.
Battery is only partially discharged. Continue to charge the battery.
The charger is making an audible clicking sound. Circuit breaker is cycling. The settings may be wrong. Check the charger settings.
Battery is defective. Have the battery checked.
Shorted battery cables or clips. Circuit breaker cycles when current draw is too high. Check for shorted cables or clips and replace if necessary.
Severely discharged battery, but otherwise it is a good battery. The battery may not want to accept a charge due to a run-down state. Allow charging to continue until battery has a chance to recover sufficiently to take a charge. If more than 20 minutes, stop charging and have the battery checked.
Reverse connections at battery. Shut the charger off and correct the lead connections.
Charger makes a loud buzz or hum. Transformer laminations vibrate (buzz). No problem; this is a normal condition.
Shorted Diode Assembly or Output Rectifier Assembly (hum). Have charger checked by a qualified technician.
Short or no start cycle when cranking engine. Drawing more than the engine start rate. Crank time varies with the amount of current drawn. If cranking draws more than the engine start rate, crank time may be less than 3 seconds.
Failure to wait 3 minutes (180 seconds) between cranks. Wait 3 minutes of rest time before the next crank.
Clips are not making a good connection. Check for poor connection at battery and frame.
AC cord and/or extension cord is loose. Check power cord and extension cord for loose fitting plug.
No power at receptacle. Check for open fuse or circuit breaker supplying A.C. outlet.
The charger may be overheated. The thermal protector may have tripped and needs a little longer to reset. Make sure the charger vents are not blocked. Wait and try again.
Battery may be severely discharged. On a severely discharged battery, charge for 10 to 15 minutes in the manual charge rate to help assist in cranking.
Charger will not turn on when properly connected. A.C. outlet is dead. Check for open fuse or circuit breaker supplying A.C. outlet.
Poor electrical connection. Check power cord and extension cord for loose fitting plug.
The battery is connected and the charger is on, but is not charging. Clips are not making a good connection. Check for poor connection at battery and frame. Make sure connecting points are clean. Rock clips back and forth for a better connection.
The measured current is much lower than what was selected. The charger reached the maximum voltage and is reducing the current. No problem; this is a normal condition.
Schumacher User Manual Link


When a charging problem arises, make certain that the battery is capable of accepting a normal charge. Double check all connections, AC outlet for a full 120-volts, charger clips for correct polarity and the quality of the connections from the cables to the clips and from the clips to the battery system. The clips must be clean.

When a battery is very cold, partially charged or sulfated, it will not draw the full rated amperes from the charger. It is both dangerous and damaging to a battery to force higher amperage into it than it can effectively use in recharging.

Sort By:
Page of 1
0099000045 Schumacher Knob For Selector Switches on SE Series Chargers 0099000045 Schumacher Knob For Selector Switches on SE Series Chargers

This Knob is for selector switches on SE Series chargers only, there are separate knobs for selector switches and timers. Please check your part numbers carefully.

Discontinued
0099000062 Schumacher 6" CW Fan Blade 0099000062 Schumacher 6" CW Fan Blade

0099000062 Schumacher 6" CW Fan Blade.

Discontinued see 316-009-000
0099000063 Schumacher Fan Motor Open Frame 115 Volt 0099000063 Schumacher Fan Motor Open Frame 115 Volt

Fan Motor Open Frame 115 Volt

Discontinued
0099000066 Schumacher Battery Charger Axle 3/8 Dia. 0099000066 Schumacher Battery Charger Axle 3/8 Dia.

0099000066 Schumacher Battery Charger Axle 3/8 Dia.15-3/8" Long.

Discontinued
0099000080 Wheel 6" Plastic For 3/8 Axle 0099000080 Schumacher Wheel 6" Plastic For 3/8 Axle

0099000080 Wheel 6" Plastic For 3/8 Axle

Discontinued
0099000094 Schumacher 135 Minute Timer Mechanical with Hold 0099000094 Schumacher 135 Minute Timer Mechanical with Hold

Mechanically controls charging in timed Mode with manual hold mode. Single Pole Single Throw (SPST) Switch rated 15 amperes. Termination is designed to accept 1/4" spade terminals.

Price $42.95
0099000096 Knob For Timer Switches 1/4" OD 3/4 "D" Shaft 0099000096 Knob For Timer Switches 1/4" OD 3/4 "D" Shaft

0099000096 Knob For Timer Switches 1/4" OD 3/4 "D" Shaft, there are separate knobs for selector switches and timers. Please check your part numbers carefully.

Discontinued
0099000123 Foot For 6" Wheeled Units 0099000123 Schumacher Foot For 6" Wheeled Units

0099000123 Foot For 6" Wheeled Units

Discontinued
0099000270 Schumacher Knob For Selector Switches on PS Series Chargers 0099000270 Knob For Selector Switches on PS Series Chargers

This Knob is for selector switches with a 3/4 Shaft only, there are separate knobs for timers with a half shaft. Please check your part numbers carefully.

Discontinued
0499000025 Schumacher 7 Position Rotary Selector Switch 0499000025 Schumacher 7 Position Rotary Selector Switch

7 Position Rotary Selector Switch

Discontinued
1199003352 Schumacher Foot, Metal 1199003352 Schumacher Foot, Metal

1199003352 Schumacher Foot, Metal, no hardware included.

Discontinued
2199700006 Axle End Cap .375 Dia Axle (Pair) 2199700006 Schumacher Axle End Cap .375 Dia Axle (Pair)

Axle End Cap Fits .375 (3/8") Diameter Axle, Sold as a Pair, Can be used on any 3/8" Axle to secure wheels.

Discontinued
2299001067 Schumacher Battery Charger Wheels - Handle - Hardware Kit 2299001067 Schumacher Battery Charger Wheels - Handle - Hardware Kit

Battery Charger Wheels - Handle - Hardware Kit For SE3000, SE6030. Includes 3599000210 Handle, 0099000080 Wheels, 0099000123 Plastic Foot, 0099000066 Axle, 2299001076 Misc Parts Bag (screws etc..)

Discontinued
2299001173 Raddital Rectifier Heatsink Kit 2299001173 Schumacher Heatsink Rectifier Assembly

2299001173 Raddital Rectifier Heatsink Kit, 300 Amp Cycle Duty, 70 Amp Continuous Duty, 8 Diode Ceramic Insulated Spider Design.

Discontinued
2299001587 Schumacher Heatsink Rectifier Assembly 2299001587 Schumacher Heatsink Rectifier Assembly

Heatsink Rectifier Assembly, requires no soldering to install. Includes 9" leads. Used on newer style units. Heavy Duty design for greater reliability. 1/4" spade terminal leads make installation a snap.

Discontinued
2299001651 Schumacher Heatsink Rectifier Assembly 2299001651 Schumacher Heatsink Rectifier Assembly

Heatsink Rectifier Assembly, requires no soldering to install. Includes 9" leads. Used on newer style units. Heavy Duty design for greater reliability. 1/4" spade terminal leads make installation a snap. *(fan speed control board sold separately)

Discontinued
2299002058 Schumacher 12 Volt Fan Motor 80mm X 80mm X 25mm 2299002058 Schumacher 12 Volt Fan Motor 80mm X 80mm X 25mm

Fan Motor provides cooling for the unit. 80mm X 80mm X 25mm 12volt DC quite design keeps noise to a minimum. If equipped, check your 2299002070 Schumacher 12volt DC Fan Speed Controller for possible fault as well.

Discontinued
2299002070 Schumacher 12 Volt DC Dual Fan Motor Control Board 2299002070 Schumacher 12 Volt DC Dual Fan Motor Control Board

12 Volt DC Dual Fan Motor Control Board. Mounts to the rectifier, fans plug into the board sockets. Requires removal of heat-sink from old board and riveted to this when installing. We recommend the purchase of 240000077 Silicone Heat Transfer Compound for proper heat transfer.

Discontinued
316-009-000 Fan Blade 6" 4 Blade CW 316-009-000 Fan Blade 6" 4 Blade CW

Fan Blade 6" 4 Blade CW. Same as 130007-001 Christie

Price $12.85
3199100028A 75 Amp 400 Volt Positive Diode (Anode On Lead) 3199100028A Schumacher 75 Amp 400 Volt Positive Diode (Set Of 4)

3199100028A 75 Amp 400 Volt Positive Diode (Anode On Lead). Press in diode, used in a wide array of applications. Once installed in the heat-sink these may require soldering to install onto transformer taps.
Use caution when replacing diodes always verify polarity or damage to equipment or self may result. Century Tool & Equipment assumes no responsibility for loss, damage or personal injury due to the miss-application of any electrical component. Purchase of this item agrees to said statement. This item should only be installed by a qualified and experienced electrician.

Discontinued
3599000662 Schumacher Battery Charger Handle Round Black Steel 3599000662 Schumacher Battery Charger Handle Round Black Steel

3599000662 Schumacher Battery Charger Handle Round Black Steel. Replaces handle part number 3599000136.

Discontinued
3899001140 Schumacher Output Cable And Clamp Black Negative 6 AWG 82" 3899001140 Schumacher Output Cable And Clamp Black Negative 6 AWG 82"

Output Cable And Clamp, Black Negative, 6 AWG Welding wire, Steel Clamp, Ring Terminal Connection, 82" long with square strain relief on cable.

Discontinued
3899001141 Schumacher Output Cable And Clamp Red Positive 6 AWG 88" 3899001141 Schumacher Output Cable And Clamp Red Positive 6 AWG 88"

Output Cable And Clamp, Red Positive, 6 AWG Welding wire, Steel Clamp, Ring Terminal Connection, 88" long with square strain relief on cable.

Discontinued
3899001968 Schumacher Output Cable And Clamp Black Negative 6 AWG 83" 3899001968 Schumacher Output Cable And Clamp Black Negative 6 AWG 83"

Output Cable And Clamp, Black Negative, 6 AWG Welding wire, Steel Clamp, Ring Terminal Connection, 83" long with square strain relief on cable.

Discontinued
3899001969 Schumacher Output Cable And Clamp Red Positive 6 AWG 88" 3899001969 Schumacher Output Cable And Clamp Red Positive 6 AWG 88"

Output Cable And Clamp, Red Positive, 6 AWG Welding wire, Steel Clamp, Ring Terminal Connection, 88" long with square strain relief on cable.

Discontinued
3999000061 Schumacher Circuit Breaker 105A 12V 3999000061 Schumacher Circuit Breaker 105A 12V

3999000061 Schumacher Circuit Breaker 105A 12V

Discontinued
3999000109 Schumacher Circuit Breaker 32 Volt DC 105 Amp 3999000109 Schumacher Circuit Breaker 32 Volt DC 105 Amp

3999000109 Schumacher Circuit Breaker 32 Volt DC 105 Amp. When ordering, it may be necessary to purchase a pair of the 5199000406 screws if replacing and older circuit breaker for retrofit.

Discontinued
51-288 115 Volt Fan Motor With Fan Blade & Mount 51-288 115 Volt Fan Motor With Fan Blade & Mount

51-288 115 Volt Fan Motor With Fan Blade & Mount. .195 diameter shaft. Your unit may not require the mount, in which case discard it.

Discontinued See ASO610190
5100000005 Timer Screw M3 X 5.5 5100000005 Timer Screw M3 X 5.5

5100000005 Screw M3 X 5.5 For Original Timer

Price $0.05
5399100084 Schumacher Ammeter Horizontal 0-80 Amp 5399100084 Schumacher Ammeter Horizontal 0-80 Amp

Ammeter Horizontal 0-80 AMP features easy snap-in installation, no tools required. Red Green Charge Rate face. 0-80 Amp range and wire through induction pick-up for greater accuracy.

Discontinued
5399100117 Ammeter Horizontal 0-80 Amp Range with Charge & Start 5399100117 Schumacher Ammeter Horizontal 0-80 Amp Range with Charge & Start

5399100117 Ammeter Horizontal 0-80 Amp Range with Charge & Start

Discontinued
5399100143 Schumacher Ammeter Horizontal 0-80 Amp 5399100143 Schumacher Ammeter Horizontal 0-80 Amp

Ammeter Horizontal 0-80 AMP features easy snap-in installation, no tools required. Yellow Orange Charge Rate face. 0-80 Amp range and wire through induction pick-up for greater accuracy.

Discontinued
6094K89 Knob For Schumacher Battery Charger Selector Switches & Timers 6094K89 Knob For Battery Charger Selector Switches & Timers

6094K89 Knob For Battery Charger Selector Switches & Timers. This Knob is for selector switches and timers, designed with 1/4" ID and a set screw for locking onto shaft. Suitable for all 1/4" shaft switches. Replaces Schumacher 0099000045 & 0099000096.

Price $4.65
TJ1-120MHB Universal Battery Charger 2 Hour Mechanical Timer TJ1-120MHB Universal Battery Charger 2 Hour Mechanical Timer

TJ1-120MB Universal Mechanical 2 Hour Timer With Finish Bell. Mechanically controls charging in timed Mode, has "Hold" for manual un-timed charging. Single Pole Single Throw (SPST) Switch rated 15 amperes. Termination is designed to accept 1/4" Quick Disconnect terminals. Includes mounting screws. Replaces many older mechanical timers.

Discontinued see 0099000094
   
 
*Variations of models due to production changes and parts availability are not our responsibility
*No refunds on electrical components
*Service should be performed only by a qualified technician
*Please read all supporting documentation and safety instructions