112699 Robinair Oil Injector O-Ring

114692 Robinair Oil Bottle Cap for Oil Inject / Drain bottle, for 8 - 12 ounce oil injector bottles. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Don't forget extra bottles (115642) for storing different oil types.

114693 Robinair Oil Bottle Cap (Less Liner With Holes) For Oil Injectors

These gaskets fit 1/4" flare and 1/2 ACME standard hose fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become crushed over time resulting in poor flow or restriction due to swelling. These are standard for some other vendors hoses as well.

12oz. Graduated Oil Drain - Oil Injector Bottle. 12oz Capacity in 1/2oz graduations and 360 Milliliters in 10 Milliliter graduations, for dispensing oil via an injector or for measuring oil removed during refrigerant recovery process. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Don forget extra caps (114692) for storing different oil types.

12oz. Graduated Oil Injector Bottle. 12oz Capacity in 1/2oz graduations and 360 Milliliters in 10 Milliliter graduations. For storing alternative oils for injection & for dispensing oil via an injector or for measuring oil removed during refrigerant recovery process. Durable plastic resists oils and dyes and most chemicals. Easily cleaned for long life. Includes cap & Level O-ring.

Optional Vacuum Pump Intake Fitting Adapter. Brass Construction. 3/8" Female Flare x 1/4" Male Flare

30lb. R-12 / Universal Gas Refillable Refrigerant Tank. Red Vapor Blue Liquid Ported Valve. 30 lb. capacity refrigerant tank for R-12, R-22, R-502 (universal) with 1/4" Flare fittings

8oz. Graduated Oil Drain - Oil Injector Bottle. 8oz Capacity in 1/2oz graduations and 240 Milliliters in 10 Milliliter graduations, for dispensing oil via an injector or for measuring oil removed during refrigernt recovery process.

50lb. R-12 / Universal Gas Refillable Refrigerant Tank. Red Vapor Blue Liquid Ported Valve. 50 lb. capacity refrigerant tank for R-12, R-22, R-502 (universal) with 1/4" Flare fittings

50 Lb. Refillable Refrigerant Tank Float Switch. Red Vapor Blue Liquid Ported Valve. 50 lb. capacity refrigerant tank for R-12, R-22, R-502 (universal) with 1/4" Flare fittings

30 Lb. Refillable Refrigerant Tank Float Switch And 3/16" Fittings For 17625a

30 Lb. Refillable Refrigerant Tank Float Switch. Red Vapor Blue Liquid Ported Valve. 30 lb. capacity refrigerant tank for R-12, R-22, R-502 (universal) with 1/4" Flare fittings

Designed to protect recovery systems from debris and deposits that would normally harm your unit. Large filter capacity provides long life. All steel construction with enamel finish resists corrosion and rusting. 1/4" inlet fitting and 3/8" outlet fittings are standard.

Power Cord - 110 Volt 16 Gauge. For heay duty cord see 551628.

Float Switch Cable Makes the connection between the float in the tank and the system relay. When the tank reaches 80% capacity, the float interrupts the control voltage to the system relay causing the unit to shut down.

Valve Stem rebuild kit, for units with old style panel valves. Identifiable by the center screw holding the stem in place with plastic removable handles. This kit does not repair "Kantleak" style valves, those must be replaced with new valves.

Gauge Lens 2.75" Diameter For 17700a / 34600 / 34700 Series, old style gauges. Check the bevel of your lens to ensure it matches this lens profile. Newer style lenses have a sharp 45 degree angled outer ring these have a arched outer ring.

Red Cap For Asco Solenoid

These gaskets fit 1/4" flare and 1/2 ACME standard fittings. If you are doing maintenance on you unit it's a good idea to replace these as well as they become smashed over time resulting in poor flow.

Designed to protect recovery systems from debris and deposits that would normally harm your unit. Large filter capacity provides long life. All steel construction with enamel finish resists corrosion and rusting. 1/4" Male Flare fittings.

CRXTOSP1 Tank Overfill Protection Cable Shorting Plug allows the user to override the tank float safety device on most recovery units using a 3 pin brad Harrison cable. Screws in place at the cable end allowing the unit to start. (Always use a scale for accuracy when using this device) 30 & 50 pound tanks should never be filled to a level beyond 80% of tank capacity.

1/4 Flare Seal Cap with anchor retention strap prevents loss when not in use.

Inlet Check Valve - 1/4 M Flare X 1/4 M Flare A two port valve, that normally allows fluid (liquid or gas) to flow through it in only one direction.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Handle
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA17434 Discontinued See 19865
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

System Relay 115 volt coil, double pole single throw normally open switch with dual sets of 15 amp contacts. Acts as a pilot from the circuit board usually carrying higher amp loads to protect smaller relays on board. Can be used for universal applications due to the high amp contact rating.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Vacuum Switch Normally closed switch that opens at 13 +/- 3" Hg and resets at 3 +/- 3" Hg. If the vacuum in the inlet is deeper than 13" Hg, the switch opens and stops the recovery or recycling process. This switch must also open to bring the unit out of clearing.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Complete Refrigerant Solenoid Assembly (120v) Includes brass body and coil. A normally closed solenoid that, when energized, allows flow. i.e. Recovery, Charge, vacuum, etc. NOTE: RA19258 Solenoid Rebuild Kit
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Compressor Oil Separator Separates any oil being carried out of the compressor and returns it to the inlet side of the compressor.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Pressure Cutout 17650 / 17655 A normally closed sensor that opens, stopping the recovery process when the compressor discharge pressure reaches 435 psi. SPDT Contact arrangement. 1/4 spade termination.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Recovery Start Switch 10 Amp 1/4 HP Momentary Orange Lighted Switch
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

High Pressure Light Provides a visual warning when high pressure is reached on the discharge side of the compressor.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Tank Full Light Provides a visual warning when the tank is full.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Upper Fan 17500B Cools compressor and electrical components inside of unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Upper Fan 17501B Cools compressor and electrical components inside of unit.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Condenser Coil Refrigerant flows through this dual pass condenser and gives up heat causing it to condense.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Inlet Stem Assembly A quick coupling mount for the inlet filter.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Oil Separator Separates oil from refrigerant. Internal heat causes incoming saturated vapor to evaporate. This is important to be sure no liquid enters the compressor and that oil droplets contained in the incoming refrigerant will drop out in the separator.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

RA19181 Robinair 115 Volt Power Cord Receptacle
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Ball Valve Assembly Discharge Valve - When open and in recovery, allows refrigerant to flow into the tank.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Discontinued Part Number (See 19427)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Discontinued Part Number (See 19427)
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Solenoid Rebuild Kit Normally closed Solenoid Rebuild Kit - Used to rebuild certain solenoids in manifolds or discrete (RA19006) etc..
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Compressor Start Kit for older style compressors (check service for applications) .
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115v Solenoid Coil Coil only, used to energize a normally closed solenoid that, when energized, allows flow. i.e. Recovery, Charge, vacuum, etc. NOTE: RA19258 Solenoid Rebuild Kit
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

Compressor Install Kit 650 Series Units To Use Cubigel Compressor Copper Lines and tubing used to retrofit unit for new style compressor.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

115 Volt Cubigel Compressor (Replaces The RA17110, RA17434, RA19458, & RA19748) Includes all hardware and electrical for a complete install. See additional plumbing retrofit kits noted for older style units.
Robinair does not warrant any "RA" repair item not installed by an Authorized Service Center.

One 1/4'' female flare to 3/8'' male flare brass adapters made in the USA using the highest level of brass consisting of 65% copper and 35% zinc which means high-tensile strength while resisting corrosion. The forging process of fittings maximize strength and eliminate cracking.