Automotive tools & equipment

HVAC & Industrial supplies

Sales - parts -service

You are here: Home > Air Conditioning Equipment > Brass Fittings > Flared Tube Fittings > Male Flare X Female Solder Elbow

Male Flare X Female Solder Elbow

JB’s American made brass SAE 45° flared tube fittings may be used with copper, brass, aluminum, steel, and plastic tube provided an acceptable fl are could be generated with the material.

Vacuum and pressures of 5,000 psi can be handled depending upon the size, material, and conditions. Using a 4:1 safety factor, the following general rule (excluding plastic tube) is used:

  • 3,000 psi to ¼"
  • 2,000 psi to ½"
  • 1,500 psi to 1"

Long nuts are recommended when vibration is a factor. Tubing should be double flared in extreme applications to minimize fl are thinning on over-tightening.

Fittings listed generally comply with SAE, ASA, ASME, and MS standards; however, when design makes dimensions critical, please contact us at 800.323.0811 for samples and/or prints for testing and evaluation.

Tube sizes listed are OD (outside diameter). To determine nominal (water tube) size, subtract 1/8", thus 5/8" OD equals 1/2" nominal.

Pipe sizes listed are standard nominal pipe size and threads are to Dryseal Taper Pipe Standards.

JB will provide flare fitting to SAE Standard J513 whenever possible. In some cases, slight deviations will occur when full compliance fittings are not available.

  • Make and break
  • Good vibration resistance (improved by using long nuts)
  • Low cost
  • Easy assembly
  • Wide selection

Heavy-duty ACR tube fittings generally conform to SAE, ASA, and ARI Standards for hydraulic, marine, and refrigeration service. Long dryseal pipe threads minimize leakage and provide more clearance for tightening flare nuts. Shapes, elbows, tees, etc., are made from brass forgings to maximize strength and eliminate cracks.

THREAD SIZE OF TUBE ENDS
O.D. TUBE
SAE/FLARE
O.D. TUBE
SAE/FLARE
1/8"
5/16-24
1/2"
3/4-16
3/16"
3/8-24
5/8"
7/8-14
1/4"
7/16-20
3/4"
1-1/16-14
5/16"
1/2-20
7/8"
1-1/4-12
3/8"
5/8-18
1"
1-3/8-12
7/16"
11/16-16
-
-

TORQUE POUNDS FOR FLARE FITTING (DRY THREAD)
SIZE
FT. LBS
1/4"
8 - 10
3/8"
15 - 25
1/2"
25 - 35
5/8"
40 - 55
3/4"
50 - 60
Sort By:
Page of 1
ES2-44 JB Industries 1/4 Male Flare x 1/4 Solder Elbow (5 Pack) ES2-44 JB Industries 1/4 Male Flare x 1/4 Solder Elbow (5 Pack)

ES2-44 JB Industries 1/4 Male Flare x 1/4 Solder Elbow (5 Pack) made in the USA using the highest level of brass consisting of 65% copper and 35% which means high-tensile strength while resisting corrosion. The forging process of fittings maximize strength and eliminate cracking.

Price $32.49
ES2-66 JB Industries 3/8 Male Flare x 3/8 Solder Elbow (5 Pack) ES2-66 JB Industries 3/8 Male Flare x 3/8 Solder Elbow (5 Pack)

ES2-66 JB Industries 3/8 Male Flare x 3/8 Solder Elbow (5 Pack) made in the USA using the highest level of brass consisting of 65% copper and 35% which means high-tensile strength while resisting corrosion. The forging process of fittings maximize strength and eliminate cracking.

Price $33.98
ES2-68 JB Industries 3/8 Male Flare x 1/2 Solder Elbow (2 Pack) ES2-68 JB Industries 3/8 Male Flare x 1/2 Solder Elbow (2 Pack)

ES2-68 JB Industries 3/8 Male Flare x 1/2 Solder Elbow (2 Pack) made in the USA using the highest level of brass consisting of 65% copper and 35% which means high-tensile strength while resisting corrosion. The forging process of fittings maximize strength and eliminate cracking.

Price $34.92
ES2-88 JB Industries 1/2 Male Flare x 1/2 Solder Elbow (2 Pack) ES2-88 JB Industries 1/2 Male Flare x 1/2 Solder Elbow (2 Pack)

ES2-88 JB Industries 1/2 Male Flare x 1/2 Solder Elbow (2 Pack) made in the USA using the highest level of brass consisting of 65% copper and 35% which means high-tensile strength while resisting corrosion. The forging process of fittings maximize strength and eliminate cracking.

Price $28.41
   
 
Male Flare X Male Pipe Elbow