OTC 3050E Noid Lite Test Kit - Noid Lites are a proven test device to quickly determine if the electrical signal is present at the fuel injector. Just plug in and turn over the engine; flashing noid indicates good signal.

IAC Lite - For checking the electronic control module signal that provides direction to the idle air control motor on General Motors vehicles with throttle body or port fuel injection systems. Signal test light for 1982 and newer GM TBI and PFI fuel injection systems with square 4-pin connector.

IAC Lite - For checking the electronic control module signal that provides direction to the idle air control motor on General Motors vehicles with throttle body or port fuel injection systems. Signal test light for 1987 and newer GM Model 700 TBI and PFI fuel injection systems with a flat 4-pin connector.

OTC 3054E Noid Lite / IAC Test Kit - Simplest method for eliminating the EFI system or idle air control as possible faults on no-start vehicles. Disconnect the fuel injectors, plug in a Noid Lite, and crank the engine. A flashing light indicates normal pulsing voltage.

3307 Assenmacher Specialty Tools Fuel Pump Wrench for VW/Audi - Wrench for removal & installation of the fuel pump. Applicable to various Volkswagen & Audi models.

This is our universal adapter set for testing injection nozzles on the most popular automotive, agricultural, and construction diesel engines.

OTC 4202 Nozzle Tester Adapter Set - These adapter expand our No. 4200 Nozlrater to troubleshoot a wide range of diesel engine injector nozzles. For servicing Audi, GM, Mercedes- Benz, Nissan / Datsun, Toyota, and VW Rabbit diesel engines.

OTC 4203 Manifold / Adapter Set - This adapter set expands the OTC 4200 Nozlrater to troubleshoot a wide range of diesel engine injector nozzles. Tests Caterpillar high- and low-pressure, capsule-type nozzles, and high-pressure, pencil-type nozzles on 1100 and 3200 series engines. Complete with OTC 39870 and 206168 adapters, low-pressure gauge (up to 1,000 PSI), cap plug and mounting brackets.

Adapter Clamp

OTC 4495 A/C and Fuel Line Disconnect Set - Use to remove A/C and fuel line quick disconnect fitting from hard-to-reach areas. Six sizes available to work on many import and domestic vehicles.

OTC 4506 Fuel Line Clamp Set - This set of two pinchers can be utilized to quickly shut off the flow from vacuum, brake and fuel lines, enabling you to pinch and hold hoses without damaging them.

OTC 5040 Cummins Injector Remover / Installer

51613 Titan Fuel & Air Conditioning Line Disconnect Tool:  This tool allows you to quickly and easily separate quick disconnect fittings on many late model vehicles.  It works on fuel lines, heater and air conditioning lines as well and will fit quick disconnects sized 3/8, 1/2, 5/8 and 3/4 of an inch.

51614 Titan Fuel Line Disconnect Tool: This tool is essential for the service and replacement of fuel filters on many late model vehicles with quick disconnect style fittings. Works on 5/16 and 3/8" fuel lines with the quick disconnect fittings and provides quick and easy separation.

LARGE DPF INLET CONE

MEDIUM DPF INLET CONE

Noid Lite F.I. (GM Multec 2)

OTC 6260 Fiber Optic Noid Lite Extension

OTC 6266 Bosch 2 Noid Light

OTC 6509 Fuel Line Disconnect Tool (3/8" & 5/16") - This tool's innovative low-profile design allows for it to be used in tight spaces and it works on the big three's (GM, Ford and Chrysler)  vehicles. Gets into places where there is limited clearance such as between the fuel line fittings and fuel filters, fuel Rails, sending units. The tool is designed to access the center port on the GM fuel tank sending unit. For 3/8" & 5/16" applications.

OTC 6511 Fuel Line Disconnect Tool (3/8" & 1/2") - This tool's innovative low-profile design allows for it to be used in tight spaces and it works on the big three's (GM, Ford and Chrysler)  vehicles. Gets into places where there is limited clearance such as between the fuel line fittings and fuel filters, fuel Rails, sending units. The tool is designed to access the center port on the GM fuel tank sending unit. For 3/8" & 1/2" applications.

OTC 6517 Fuel & A/C Disconnect Set (9 piece) - Designed for A/C lines, fuel lines, and transmission cooler lines.

6550MAN-13 OTC Fuel Injection Applications Guide - Over 200 pages of valuable fuel system service information for professional technicians. English, Spanish and French translations for: Safety precautions and Fuel system, adapter, and tool identification.

6554 OTC Fuel / Ac Line Disconnect Kit - The new OTC 6554 Fuel and AC Line Disconnect Kit provides technicians with a great selection of disconnect tools - intended for top-side vehicle service. We've included ONLY the disconnect tools needed for vehicles on the road today and ONLY tools intended for Fuel and AC lines in the OTC 6554.

OTC 6599 Fuel Tank Lock Ring Wrench - This tool's universal design allows the tool to fit fuel tank lock rings on Ford, Chrysler, and GM vehicles.

GM FUEL LINE DISCONNECT TOOL

OTC 6752 Fuel Injector Storage Rack - Fuel injector storage rack with durable plastic protectors. Compartment are marked to help keep the injectors organized by the cylinder they came from in order to keep the injector calibration in sync with the vehicles ECM.

OTC 6753 Plastic Protector Cups for 6752 - Durable plastic protectors cup. A set of eight replacement cups for 6752 Fuel injector storage rack.

6754 OTC Diesel Fuel Pressure Gauge - Designed to test fuel pressure on GM Duramax diesel engines.

OTC 6760 FORD 6.0L & 7.3L Fuel Filter Wrench - The new 6760 Fuel Filter Wrench is designed to remove and install the fuel filters on the Ford 6.0L & 7.3L Power Stroke diesel engines as well as International / Navastar diesel engines.

OTC 6763 Ford 6.0L Fuel High Pressure Fuel Rail Adapters - This pair of High Pressure Fuel Rail Adapters is required to connect to the vehicle's fuel line. The fuel line connection changed in 2004 – so the two adapters give you the capability to address either platform for pressure testing.

OTC 6764 Ford 6.0L Diesel IPR Controller - When a hard start or no start condition exists, the 6764 from OTC allows a technician to close the Injector Pressure Regulator in order to determine if proper injector control pressure is achieved and sustained for the starting process.

OTC 6765 Ford 6.0L Inject Pressure Regulator Socket - This IPR Socket actually combines two OE tools into one. Again, the configuration for the IPR changed in 2005 and a second tool was developed for the change. However, our Aftermarket engineers worked with specialized technicians to develop one tool that can address either version of the IPR – giving today's technicians a cost-effective tool.

OTC 6766 Ford 6.0L Terminal Release Tool - This Terminal Release Tool is required for removal of the vehicle's injector wiring harness without causing damage to the component.

OTC 6768 Ford 6.0L Glow Plug Release Tool -  Safely remove and install the glow plug harness on 2004-2009 Ford 6.0L Diesel engines.

6778 OTC Injector Puller Duramax 6.6 - Designed to pull injectors on a GM Duramax 6.6L engine, 2001 - 2004.

6779 OTC Injector Puller GM Duramax - Designed to pull injectors on a GM Duramax 6.6L engine, 2005 - 2011

OTC 7337 Ford Fuel Line Disconnect Tool Set - These tools will easily disconnect the spring lock couplings of fuel lines on Ford's throttle body and port fuel injection systems.

OTC 7361 Fuel Line Disconnect Tools - These little fuel line disconnect tools are just right for working on quick disconnect fuel lines.

OTC 7363 Fuel Line Disconnect Tool Set - This set works on quick connect fuel lines on Ford, GM, and Chrysler, and on the spring lock fuel line couplings on Ford's popular PFI system.

Ford Fuel Line Plug

Fuel Line Wrench

OTC 7454 Fuel Injector Nozzle Puller - Pulls fuel injection nozzles on Ford 6.9L/7.3L and Navistar DT466/9L diesel engines.

OTC 7455 Fuel Injector Nozzle Puller / Installer

OTC 7458 Bosch Nozzle Socket - Multipurpose tool for removing or installing injector nozzles. Use the inner socket to hold the nozzle stationary, and the outer socket to loosen or tighten the nozzle's gland nut.

OTC 7460 Diesel Fuel Line Wrench - Fuel line nuts are often hard to reach, but these unique 3/8" square-drive tools solve that problem. With them, you can loosen or tighten fuel lines at the fuel injector nozzle or fuel injection pump without damaging the nut.

OTC 7601 Ford TBI Noid Lite - Noid Lites are a proven test device to quickly determine if the electrical signal is present at the fuel injector.Just plug in and turn over the engine; flashing noid indicates good signal.

OTC 7602 GM PFI Noid Lite - Noid Lites are a proven test device to quickly determine if the electrical signal is present at the fuel injector.Just plug in and turn over the engine; flashing noid indicates good signal.

OTC 7608 Geo TBI Noid Lite - Noid Lites are a proven test device to quickly determine if the electrical signal is present at the fuel injector.Just plug in and turn over the engine; flashing noid indicates good signal.

8010 Assenmacher Specialty Tools 1/4" Ford Mustang Fuel Line Remover - Used for the removal of 1/4" return lines on the fuel pump. Applicable: [1995–1996] Ford® Mustang.

8011 Assenmacher Specialty Tools Replacement Rubber Band for Disconnect Tools

8012 Assenmacher Specialty Tools 5/16" Ford Fuel Filter Disconnect Tool - Made of red-anodized aluminum. Used for R & R of fuel filter & 5/16" return line from the fuel pump-sending unit. Applicable for Ford® Aerostar, Bronco, E-Series, Explorer, F-Series, and Ranger models as well as the Saab® 900.

8013 Assenmacher Specialty Tools 3/8" Ford Fuel Line Disconnect Tool - Used for removing 3/8" fuel lines & feed lines from the fuel pump-sending unit. Applicable to Ford® Aerostar, Bronco, E-Series, Explorer, F-Series and Ranger models as well as the Saab® 900.

8022 Assenmacher Specialty Tools GM Fuel Filter Disconnect Tool FUEL FILTER - Used for the R & R of the fuel filter. Applicable: [2002-2004] Chevrolet® Tahoe & Suburban.

8026 Assenmacher Specialty Tools 5/16" Nissan/Toyota Fuel line Disconnect Tool - 5/16" Fuel Line Disconnect Tool. Used for disconnecting the fuel line from the fuel rail. Applicable: [2004–newer] Nissan® & Toyota® models.

8027 Assenmacher Specialty Tools GM Duramax Fuel Injector Disconnect Tool - Used for removing the fuel line from the indirect fuel injector. Made of Orange-Anodized Aluminum. Used during R & R of Fuel Lines. Applicable: [2011] GM® w/ 6.6L [V8] turbo diesel Duramax engine [2011] Chevrolet® Silverado 2500 and [2011] GMC® Sierra 2500.

8028 Assenmacher Specialty Tools Subaru Fuel Line Disconnect Tool. Comparable to Subaru #18371AA000 and #42099AE00. Applicable: (2004–newer) 2.0L and 2.5L turbo engines, 2.5L naturally aspirated engines (except 2006 WRX/STI).

Energize a fuel pump by the push of a switch

The relay Bypass Switch Kit with Amp Loop allows circuit bypass and current testing for 12V DC relays

BMW4622 Assenmacher Specialty Tools Fuel Level Sensor Lock Ring Tool: Used to remove the fuel level lock ring. Comparable to BMW factory tool number #161020.

BMW9054 Assenmacher Specialty Tools BMW Fuel Injector Seal R&R Set - Set used to install new seals onto the injectors. Applicable: BMW® N14, N18, N54 & N63 engines.

CKV7 3/8” Universal Fuel Check Valve

CP2015 Assenmacher Specialty Tools BMW Clamp Pliers: Used to crimp BMW fuel hose clamps.

FID8838A2 Injector Harness Tester (Blue-Point®). For use on Bosch® 2 injectors used on 2000–later Cadillac® 4.6 L V8 and Oldsmobile® 4.0 L V8 engines

5/16" Nylon Tubing 25'

3/8" Nylon Tubing 25'

Pk/2 5/16" Nly-Stl Cmprssn Ftg

Pk/2 5/16" Nyl-Stl Push-On Un

Pk/2 3/8" Nyl-Stl Cmprssn Ftg

Pk/2 3/8" Nyl-Stl Push-On Uni

Pk/2 5/16" GM Line Adapter

Pk/2 3/8" GM Line Adapter

5/16" GM Fml-Nyl Adapter

3/8" GM Fml-Nyl Adapter

Pk/2 5/16" Nyl-Hose Connector

Pk/2 3/8" Nyl-Hose Connector

Pk/2 5/16" Quick Cnnct-Nyl Con

Pk/2 3/8" Quick Cnnct-Nyl Con

Pk/10 5/16" Seal Clamp

Pk/10 3/8" Seal Clamp

Pk/2 3/8"-3/8" Str Push Conn.

Pk/2 3/8"-5/16" Str Push Conn

Pk/2 5/16"-3/8" Str Push Conn.

Pk/2 5/16"-5/16" Str Push Conn

KP1200 Fuel Line Replacement Kit

Pk/2 3/8"-3/8" 90 Dgr Push Con

Pk/2 3/8"-5/16" 90 Dgr Push Cn

Pk/2 5/16"-5/16" 90 Dgr Conn

M2010ACP Assenmacher Specialty Tools Angled MB Fuel/Evap Hose Clamp Pliers - Angled Fuel/EVAP Clamp Pliers used for the replacement of Fuel/EVAP hose clamps on newer vehicles. Also used as an aid during removal. Applicable: newer vehicles with click style hose clamps.

MVW2050F Assenmacher Specialty Tools Fuel Line Pliers: Fuel line pliers for VW/Audi fuel lines with plastic snap-together connectors, & for Mercedes 163 M-Class fuel filters (Comparable to MB# 163589003700). Also applicable to some Fiat, GM & Opel gas engine vehicles.