Automotive tools & equipment

HVAC & Industrial supplies

Sales - parts -service

You are here: Home > Plasma Cutter Parts > 118-014 YA5550 Snap-On 55 amp plasma cutter

118-014 YA5550 Snap-On 55 amp plasma cutter



118-014 Replacement Parts List
Item No.
Part No.
Description
1
412-328-016
Foot
2
410-617-016
Base
3
413-030-666
Wheel with Hub
4
413-048-666
Axle
5
412-329-016
Wheel Mounting Brackets
6
252-004-666
Pressure Switch
7
246-206-666
Solenoid
8
410-618-026
Front Panel
9
880-102-666
Circuit Board
10
254-004-666
Regulator
11
251-003-666
Pressure Gauge
12
238-285-100
Torch Assembly
13
44050
O-Rings
14
44510
High Current Nozzles (5)
15
44540

16
44530
Nozzle Cap
17
44500
Electrodes (3)
18
44520
Swirl Ring
19
238-228-666
Ground Cable Assembly
20
312-117-666
Nose
21
880-180-666
10 Pin Wire Harness
22
880-132-666
9 Pin Wire Harness
23
246-219-000
Run / Setup Switch
24
246-220-000
Amperage Selector Switch
25
246-218-666
Power Switch
26
246-477-666
Knob
27
246-199-666
Pilot Arc Relay
28
880-136-008
Transformer
29
880-106-888
Control Transformer 230 Volt AC to 20 & 24 Volt AC
30
244-080-666
Rectifier
31
254-005-666
Pre-Regulator (set at 105 PSI)
32
245-105-666
2 Ohm, 420 Watt Resistor
33
239-129-666
Terminal Block
34
216-053-666
Thermostat
35
216-086-666
Fan Motor, 230 Volt AC
36
316-007-300
Fan Blade
37
410-629-016
Back Panel
38
248-214-666
Power Cord
39
246-165-666
Contactor
40
880-134-666
1.5 Ohm, 160 Watt Resistor
41
880-137-888
Reactor
42
412-330-016
Handle
43
410-630-076
Cover with Access Panel
44
410-530-016
Access Panel
Sort By:
001-288-908 Plasma Torch Hand Grip (Trigger On Bottom) 001-288-908 Plasma Torch Hand Grip (Trigger On Bottom)

001-288-908 Plasma Torch Hand Grip (Trigger On Bottom). Used on 50-55 Amp Models 118-014 (YA5550), 118-015 (2050), 118-016 (82050,5Z031A, 5Z031B)

Price $54.38
002-244-908 Plasma Torch Safety Trigger. Used on 50-55 Amp Models 118-014 (YA5550), 118-015 (2050), 118-016 (82050,5Z031A, 5Z031B) 002-244-908 Plasma Torch Safety Trigger

002-244-908 Plasma Torch Safety Trigger. Used on 50-55 Amp Models 118-014 (YA5550), 118-015 (2050), 118-016 (82050,5Z031A, 5Z031B)

Price $24.82
098-142-000 Synthetic Lubricant 1/4oz 4424 098-142-000 Synthetic Lubricant 1/4oz 4424

Synthetic Lubricant for plasma torch O-rings

Price $19.18
131-280-908 Century Torch Standoff Repl. 4416 / 44160 131-280-908 Century Torch Standoff Repl. 4416 / 44160

Century / Solar Plasma Torch Stand-Off Kit keeps nozzle clear of dirt, paint and corrosion. Also simplifies cutting with straightedge or pattern. 131-280-908 TORCH STANDOFF Replaces 4416 / 44160.

Discontinued
216-082-000 Fan Motor With Leads 240 Volt 216-082-000 Fan Motor With Leads 240 Volt

216-082-000 Fan Motor With Leads 240 Volt .20 amps C.W. shaft end. Replaces some older models. 216-086-000, 216-086-010, 216-034-000, 216-034-100, 216-034-200, 216-034-666. See 316-007-300 for Fan blade.

Price $42.95
216-086-666 Fan Motor W/ Leads 240 Volt 216-086-666 Fan Motor W/ Leads 240 Volt

216-086-666 Fan Motor W/ Leads 240 Volt .55 amp C.W. shaft end rotation. Replaces 216-034-000, 216-034-100, 216-034-200, 216-034-666. See 216-082-000 as a possible replacement.

Discontinued
238-285-100 Plasma Torch Assembly 238-285-100 Plasma Torch Assembly

238-285-100 Plasma Torch Assembly

Discontinued See 238-456-000
238-285-999 Plasma Torch Head (Old Style Trigger On Top) 238-285-999 Plasma Torch Head (Old Style Trigger On Top)

238-285-999 Plasma Torch Head (Old Style Trigger On Top) See 238-456-000 for new style with trigger on the bottom.

Discontinued See 238-456-000
238-456-999 Plasma Torch Head (New Style Trigger On Bottom) 238-456-999 Plasma Torch Head (New Style Trigger On Bottom)

238-456-999 TORCH HEAD FOR 238-456-000, 50 Amp ,Replaces 238-285-000, 238-285-100. Used on 50-55 Amp Models 118-014 (YA5550), 118-015 (2050), 118-016 (82050,5Z031A, 5Z031B).

Discontinued See 238-456-000
244-080-666 Century Rectifier Plasma 244-080-666 Century Rectifier Plasma

244-080-666 244-076-666 Century Rectifier Plasma

Price $204.95
245-105-666 Century 2 Ohm 420 Watt Resistor 245-105-666 Century 2 Ohm 420 Watt Resistor

245-105-666 Century 2 Ohm 420 Watt Resistor comes with mounting brackets, insulators and mounting harware.

Price $272.22
246-086-666 Century Solenoid 24 Volt Air Service, replaces 246-212-666 and 43700008. 246-086-666 Century Solenoid 24 Volt Air Service

246-086-666 Century Solenoid 24 Volt Air Service, replaces 246-212-666 and 43700008, B7161370.

Discontinued
246-176-666 Switch 2 Position Rocker 16 Amp SPDT 246-176-666 Switch 2 Position Rocker 16 Amp SPDT

SPDT Switch 16 amp Rating Snap-in mount no tools required to install, 1/4 Spade terminals.

Price $15.00
246-199-666 Pilot Arc Relay 24 Volt DC Coil 246-199-666 Pilot Arc Relay 24 Volt DC Coil

246-199-666 Pilot Arc Relay 24 Volt DC Coil

Price $69.95
246-219-666 Run Set-Up Switch 2 Position Rocker 246-219-666 Run Set-Up Switch 2 Position Rocker

246-219-666 Discontinued See 246-176-666 Run Set-Up Switch 2 Position Rocker SPDT Switch 16 amp Rating Snap-in mount no tools required to install, 1/4 Spade terminals.

Discontinued See 246-217-666
246-220-666 Century 5 Position Selector Switch 246-220-666 Century 5 Position Selector Switch

246-220-666 Century 5 Position Selector Switch

Price $119.18
252-004-666 Century Switch, Air Pressure Service 252-004-666 Century Switch, Air Pressure Service

252-004-666 Century Switch, Air Pressure Service

Price $84.03
254-005-666 Century Pre-Regulator (set at 105PSI) 254-005-666 Century Pre-Regulator (set at 105PSI)

254-005-666 Century Pre-Regulator (set at 105PSI)

Price $110.18
312-114-000 Handle Both Sides 312-114-000 Handle Both Sides

Plasma Torch Handle Assembly, no hardware included. Molded handles only

Price $53.83
334-274-100 Trigger Assembly Replaces 334-281-100 334-274-100 Trigger Assembly Replaces 334-281-100

334-274-100 Trigger Assembly Replaces 334-281-100

Price $34.10
334-287-908 Electrode Plasma 50 Amp 3 Pack Repl. 4450 44500 334-287-908 Electrode Plasma 50 Amp Repl. 4450 44500 (3 pack)

Century / Solar Style Electrode. Plasma Cutting Electrodes initiate the high intensity cutting arc and provide the contact necessary for arc maintenance. Electrodes are subject to wear, causing arc to weaken or be intermittent.

Price $24.85 3 Pack
334-287-908L Electrode Plasma Extended 50 Amp 3 Pack 334-287-908L Electrode Plasma Extended 50 Amp 3 Pack

Century / Solar Style Electrode. Plasma Cutting Electrodes initiate the high intensity cutting arc and provide the contact necessary for arc maintenance. Electrodes are subject to wear, causing arc to weaken or be intermittent.

Price $26.85 3 Pack
334-288-908 Swirl Ring Plasma 50 Amp Repl. 4452 44520 334-288-908 Swirl Ring Plasma 50 Amp Repl. 4452 44520

Century / Solar Style Plasma 50 Amp Swirl Ring. Swirl Ring imparts a swirling current to stabilize the arc. Keep your plasma cutter working at peak performance with these replacement parts.
For plasma torch 238-285-100 or 238-456-000. The 334-288-908 replaces 4452, 44520, 334-288-000, 334-288-100, 334-288-500. Used on Century made model numbers: 118-014 (YA5550), 118-015 (Solar 2050, 2050C), 118-016 (82050, 5Z031A, 5Z031B)

Price $26.50 Each
334-289-908 Nozzle Plasma High Current 50 Amp 5pk 4451 44510 334-289-908 Nozzle Plasma High Current 50 Amp 5pk 4451 44510

Century - Solar Style 50 Amp High Current Plasma Cutting Nozzles (used on 45 50 & 55 amp settings). The Plasma Cutting Nozzle controls arc for smooth cutting. When Purchasing a pair of Nozzles and nozzle caps, they must be the same style and amp rating (i.e. tapered, 15/20 amp).

Price $26.95 5 Pack
334-289-908L Nozzle Plasma High Current Extended 50amp 5pk 334-289-908L Nozzle Plasma High Current Extended 50amp 5pk

High Current Extended Plasma Nozzles 50amp 5pk. The Plasma Cutting Nozzle controls arc for smooth cutting. When Purchasing a pair of Nozzles and nozzle caps, they must be the same style and amp rating (i.e. tapered, 15/20 amp).

Price $32.95 5 Pack
334-290-908 Nozzle Cap Plasma 50amp Extended Type Repl.  4453 44530 334-290-908 Nozzle Cap Plasma 50amp Extended Type Repl. 4453 44530

Century / Solar Style Nozzle Cap, Extended Type. Nozzle Caps direct cooling air flow to the nozzle and workpiece.

Price $24.00 Each
334-295-908 Nozzle Plasma Low Current 35-40 Amp 3pk 4454 44540 334-295-908 Nozzle Plasma Low Current 35-40 Amp 3pk 4454 44540

Century - Solar Style 35 - 40 Amp Low Current Plasma Cutting Nozzles. The Plasma Cutting Nozzle controls arc for smooth cutting. When Purchasing a pair of Nozzles and nozzle caps, they must be the same style and amp rating (i.e. tapered, 15/20 amp).

Price $24.95 3 Pack
512-087-908 O-Rings 20/40 15 20 50 Amp 2 pack Repl. 4405 44050 512-087-908 O-Rings 20/40 15 20 50 Amp 2 pack Repl. 4405 44050

Century / Solar Package of 2 O-Rings for 20/40, 15, 20 and 50 amp plasma cutters. The rubber O-Ring prevents air leaks which cause erratic cutting and cooling.

Price $3.32 2 Pack
Snap-On YA5550 Plasma Cutter Owners Guide Instruction Manual Snap-On YA5550 Plasma Cutter Owners Guide Instruction Manual

This Operators manual provides specific information for your model. This manual contains information such as the Important Safety Instructions, Usage and Maintenance of your PLasma Cutter. This document is provided as a download PDF format. We suggest you save it to your computer for future reference.
Model Coverage: YA5550

Price $8.00
   
 
118-014 YA5550 Snap-On 55 amp plasma cutter